Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 337 / 516

background image

• 100G-LC-C, 10x10G-LC, or CFP-LC
• EDRA1-26, EDRA1-35, EDRA2-26, or EDRA2-35

Use the standard brackets directly to mount the ONS 15454 M6 shelf.

Step 5

Align the screw holes on the left front air deflector with the screw holes on the left side of the chassis.

Step 6

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 7

Return to your originating procedure (NTP).

DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the
ONS 15454 M6 Shelf for ETSI Rack Configuration

This task installs the bracket with air deflectors (front-to-back) on the ONS 15454
M6 shelf for ETSI rack configuration.

The air deflectors can be installed only in the front position of the
chassis.

Note

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves, on page 20

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

Procedure

Step 1

Place the right front air deflector flush against the right side of the chassis (see Diagram 1 of

Mounting the Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on
page 308

Step 2

Align the screw holes on the right front air deflector with the screw holes on the right side of the chassis.

Step 3

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4

Place the left back air deflector flush against the chassis as shown in Diagram 2 of

Figure 207: Mounting the

Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 308

.

Cisco ONS 15454 Hardware Installation Guide

307

Installing the ONS 15454 M6 Shelf

DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

«
...
335
336
337
338
339
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: H&S Pages: 32

Brand: ADLINK Technology Pages: 64

StorCenter Pro 400e

Brand: Iomega Pages: 16

Brand: IEI Technology Pages: 8

Brand: National Instruments Pages: 6

Brand: Optical Systems Design Pages: 12

Brand: nMedia Pages: 4

Brand: nMedia Pages: 4

Brand: nMedia Pages: 7

Brand: nMedia Pages: 8

Brand: nMedia Pages: 9

Brand: nox Pages: 13

Brand: nox Pages: 13

Brand: CSN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands