Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 374 / 516

background image

Figure 241: Connectors on ECU-60V Faceplate

ECU-S

ECU-S is a new type of ECU introduced in Release 10.5.2 for ONS 15454 M6. The ECU-S module also
discovers and manages the inventory of the external shelf units. It also handles the multishelf management
connections and timing synchronizations. The ECU-S module available for the ONS 15454 M6 shelf is
15454-M6-ECU-S=. The ONS 15454 M6 ECU-S is backward-compatible with Release 10.1, 10.3, and 10.5.
However, there is a small difference in the port numbers detected. The details are listed in the section below.

The NCS 2006 ECU-S should not be used when the shelf is powered at –60V DC nominal input voltage.

Note

The following figure shows the ONS 15454 M6 ECU-S connectors.

Figure 242: Connectors on the ONS 15454 M6 ECU-S Faceplate

1 SCSI with 26 poles for TNC relay contact, including ACO signal and digital I/O signals

1

USB 2.0 ports (Ports A1, A2, A3, A4) and USB 3.0 port (Port A5)

2

VOIP/UDC port (RJ-45 port)

3

EMS port (RJ-45 port)

4

Three MSM ports

5

BITS1 input and output ports

6

BITS2 input and output ports

7

Three MSM ports

8

Craft terminal port

9

VOIP/UDC port (RJ-45 port)

1

0

USB 2.0 ports (Ports B1, B2, B3, B4) and USB 3.0 port (Port B5)

1

1

1 SCSI with 26 poles for digital I/O signal

1

2

The ONS 15454 M6 ECU-S supports IEEE1588v2 PTP, time-of-day (ToD), and pulse-per-second (PPS)
inputs. To support high power USB devices, ONS 15454 M6 ECU-S provides a current of 500 mA to each
of the ports. The IMPROPRMVL alarm is raised in CTC when the ECU-S is removed from the NCS 2006
shelf.

Cisco ONS 15454 Hardware Installation Guide

344

Installing the ONS 15454 M6 Shelf

ECU-S

«
...
372
373
374
375
376
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: ICP Pages: 19

Brand: nMedia Pages: 6

Ethernet Routing Switch 8010

Brand: Nortel Pages: 16

Brand: Pitney Bowes Pages: 336

Brand: Supermicro Pages: 128

Brand: SilverStone Pages: 12

1U Rackmount Chassis Kit R10-A2P4

Brand: Asus Pages: 34

Brand: Philips Pages: 111

Brand: Philips Pages: 87

Brand: Philips Pages: 46

Brand: Philips Pages: 76

Brand: Philips Pages: 71

Brand: Philips Pages: 79

Brand: Philips Pages: 71

Brand: Philips Pages: 69

Brand: Philips Pages: 80

CommPlete CC9648

Brand: Multi-Tech Pages: 26

Brand: CTC Union Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands