Cisco ONS 15454 Hardware Installation Manual Download

Page: 472 / 516

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,
GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with
a new air filter.

Note

Procedure

Step 1

Open the front door of the shelf assembly (see

NTP-G259 Open and Remove the Standard Door of the ONS

15454 M6 Shelf , on page 327

). If the shelf assembly does not have a front door, continue with Step 3.

Step 2

(Optional) Complete the

DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf , on page 330

remove the front door. If you do not want to remove the door, proceed to Step 3.

Step 3

Push the retention feature present on the right side of the shelf assembly to the left side (see the following
figure).

Figure 292: Replacing the Air Filter

Step 4

Extract the air filter from the shelf assembly (see the following figure).

Cisco ONS 15454 Hardware Installation Guide

442

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands