background image

16 1200-Watt DC-Input Power Supply Replacement Instructions

Translated Safety Warnings

Avvertenza

Il telaio va sollevato da due persone. Afferrare il telaio al di sotto del bordo inferiore

e sollevare con entrambe le mani. Per evitare infortuni, mantenere la schiena diritta e sollevare il
peso con le gambe, non con la schiena. Per evitare danni al telaio ed ai componenti, non provare mai
a sollevare il telaio tramite le maniglie sugli alimentatori o sui processori di interfaccia oppure
tramite i pannelli in plastica sulla parte anteriore del telaio. Queste maniglie non sono state
progettate per sostenere il peso del telaio.

Advarsel

Det er nødvendig med to personer for å løfte kabinettet. Ta tak i kabinettet under den

nedre kanten, og løft med begge hender. Unngå personskade ved å holde ryggen rett og løfte med
bena, ikke ryggen. Unngå skade på kabinettet og komponentene ved å aldri prøve å løfte kabinettet
etter håndtakene på strømforsyningsenhetene, grensesnittprosessorene eller i plastpanelene foran på
kabinettet. Disse håndtakene er ikke beregnet på å tåle vekten av kabinettet.

Aviso

São necessárias duas pessoas para levantar o chassis. Agarre o chassis imediatamente abaixo

da margem inferior, e levante-o com ambas as mãos. Para evitar lesões, mantenha as suas costas
direitas e levante o peso com ambas as pernas, sem forçar as costas. Para prevenir danos no chassis
e nos seus componentes, nunca tente levantá-lo pelas asas das unidades abastecedoras de energia,
nem pelos processadores de interface, ou pelos painéis plásticos localizados na frente do chassis.
Estas asas não foram criadas para suportar o peso do chassis.

¡Advertencia!

Se necesitan dos personas para levantar el chasis.  Sujete el chasis con las dos manos

por debajo del borde inferior y levántelo.  Para evitar lesiones, mantenga la espalda recta y levántelo
con la fuerza de las piernas y no de la espalda. Para evitar daños al chasis y a sus componentes, no
intente nunca levantar el chasis por las asas de las fuentes de alimentación o de los procesadores de
interfase, ni por los paneles de plástico situados en el frontal del chasis.  Las asas no han sido
diseñadas para soportar el peso del chasis.

Varning!

Det krävs två personer för att lyfta chassit. Fatta tag i chassit under den nedre kanten och

lyft med båda händerna. För att undvika skador skall du hålla ryggen rak och lyfta med benen, inte
ryggen. Chassit och delarna kan skadas om du försöker lyfta chassit i handtagen på
strömförsörjningsenheterna eller gränssnittsprocessorerna, eller i plastpanelerna på chassits
framsida. Handtagen är inte konstruerade för att hålla chassits tyngd.

Lightning Activity Warning

Warning

Do not work on the system or connect or disconnect cables during periods of lightning

activity.

Waarschuwing

Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te

werken of kabels aan te sluiten of te ontkoppelen.

Varoitus

Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.

Attention

Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.

Warnung

Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine

ab, wenn es gewittert.

Avvertenza

Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con

fulmini.

Advarsel

Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller

lyner.

Aviso

Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo

(trovoada).

Summary of Contents for PWR-7513-DC



























Reviews: