Cisco QSFP+ Series Installation Note Download | Manualshive

Page: 3 / 24

background image

3

Cisco 40-Gigabit QSFP+ Transceiver Modules Installation Note

OL-24862-01

Overview

Table 1

lists the different QSFP+ transceiver module types.

Note

The multiple-fiber push-on (MPO) connectors and the duplex LC connectors on the optical QSFP+
transceivers support network interface cables with either Physical contact (PC) or Ultra-Physical Contact
(UPC) flat-polished face types. The MPO connectors and the duplex LC connectors on the optical
QSFP+ transceivers do not support network interface cables with an angle-polished contact (APC) face
type.

Table 1

40-Gigabit QSFP+ Transceiver Modules

QSFP+ Transceiver Module
Product Number

Description

QSFP-H40G-CU1M=

Cisco 40GBASE-CR4 QSFP+ passive direct-attach copper transceiver
module assembly, 1 meter

QSFP-H40G-CU3M=

Cisco 40GBASE-CR4 QSFP+ passive direct-attach copper transceiver
module assembly, 3 meter

QSFP-H40G-CU5M=

Cisco 40GBASE-CR4 QSFP+ passive direct-attach copper transceiver
module assembly, 5 meter

QSFP-H40G-ACU7M=

Cisco 40GBASE-CR4 QSFP+ active direct-attach copper transceiver
module assembly, 7 meter

QSFP-H40G-ACU10M=

Cisco 40GBASE-CR4 QSFP+ active direct-attach copper transceiver
module assembly, 10 meter

QSFP-4SFP10G-CU1M=

Cisco 40GBASE-CR4 QSFP+ to 4 10GBASE-CU SFP+ passive
direct-attach copper transceiver assembly, 1 meter

QSFP-4SFP10G-CU3M=

Cisco 40GBASE-CR4 QSFP+ to 4 10GBASE-CU SFP+ passive
direct-attach copper transceiver assembly, 3 meter

QSFP-4SFP10G-CU5M=

Cisco 40GBASE-CR4 QSFP+ to 4 10GBASE-CU SFP+ passive
direct-attach copper transceiver assembly, 5 meter

QSFP-4X10G-AC7M=

Cisco 40GBASE-CR4 QSFP+ to 4 10GBASE-CU SFP+ active
direct-attach copper transceiver assembly, 7 meter

QSFP-4X10G-AC10M=

Cisco 40GBASE-CR4 QSFP+ to 4 10GBASE-CU SFP+ active
direct-attach copper transceiver assembly, 10 meter

QSFP-40G-SR4=

Cisco 40GBASE-SR4 QSFP+ transceiver module for MMF, multi-fiber
MPO connector

QSFP-40G-CSR4=

Cisco 40GBASE-CSR4 QSFP+ transceiver module for MMF, multi-fiber
MPO connector

QSFP-40GE-LR4=

Cisco 40GBASE-LR4 QSFP+ transceiver module for SMF, duplex LC
connector

«
1
2
3
4
5
...
»

Summary of Contents for QSFP+ Series

























Reviews:

No comments

Related manuals for QSFP+ Series

Brand: Yaesu Pages: 34

Brand: Yaesu Pages: 26

Brand: Yaesu Pages: 2

Brand: Yaesu Pages: 22

Brand: Yaesu Pages: 68

Brand: Ham Pages: 37

Brand: Yamaha Pages: 8

Brand: Yaesu Pages: 5

Brand: Xblitz Pages: 76

Brand: National Instruments Pages: 43

Brand: IDS Pages: 2

Brand: Yaesu Pages: 32

Brand: Horizon Hobby Pages: 23

Brand: AOR Pages: 1

Brand: First Alert Pages: 1

Brand: Sansui Pages: 28

Brand: DAITEM Pages: 44

Brand: Questtel Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands