background image

Three people are required to lift the rack. Grasp the rack underneath the lower edge and lift with both hands.
To prevent injury, keep your back straight and lift with your legs, not your back.

Warning

The Cisco R42612 rack weighs over 300 pounds. you will need a forklift, chain hoist, or professional mover
to remove the rack from the pallet and move it to the installation location.

Caution

If you must move the Cisco R42612 rack after installation, remove UCS and other installed components and
move them separately.

Caution

Install the heaviest devices at the bottom of the Cisco R42612 rack.

Caution

If you have multiple cabinets joined together, they must be disconnected before moving.

Caution

Removing the Cisco Cisco R42612 Rack from the Pallet

To remove the Cisco Cisco R42612 rack from the pallet, follow these steps:

Procedure

Step 1

Read the safety information before you move the Cisco R42612 rack off the pallet.

Step 2

Because the weight of the empty or populated Cisco R42612 rack cabinet is significant, be sure to have enough
trained movers to move the cabinet off the pallet and to its installation site.

Step 3

Use a 3/8" or 1/2" flat-blade screwdriver to raise the four leveling feet (one per corner) to their highest position
so that you can roll the rack on its casters. See the following figure.

Cisco R42612 Rack and RP-Series Metered Input PDU Installation Guide

21

Unpacking the Rack

Removing the Cisco Cisco R42612 Rack from the Pallet

Summary of Contents for R42612 R Series

























































































Reviews: