background image

3

RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide

78-12288-02

Installation Requirements

Installation Requirements

Before upgrading the bootflash SIMM, pay attention to the following sections:

Software and Bootflash Prerequisites, page 3

Tools and Parts Required, page 4

Safety Guidelines, page 4

Software and Bootflash Prerequisites

The minimum software and bootflash requirements are listed in Table 1. The Cisco IOS releases listed
in Table 1 apply to all Cisco 7500 series routers except for the Cisco 7576, which requires Cisco IOS
Release 11.1(22) CC or a later release of 11.1 CC.

Table 1

RSP4+ Minimum Software and Bootflash Memory Requirements

Cisco IOS Release Version

Minimum Cisco IOS Supported Release

1

1.

 Applies to all platforms that support the RSP4+ except Cisco 7576, which requires Cisco IOS Release 11.1(22)CC or a later release of 11.1 CC.

Minimum Boot-

flash Memory

Cisco IOS Release 11.1(8)CA

Cisco IOS Release 11.1(8)CA or later release of Cisco IOS Release
11.1 CA

8 MB

Cisco IOS Release 11.1(17)CC

Cisco IOS Release 11.1(17)CC or later release of Cisco IOS Release
11.1 CC

8 MB

Cisco IOS Release 11.2(6)P

Cisco IOS Release 11.2(6)P or later release of Cisco IOS Release 11.2 P

8 MB

Cisco IOS Release 11.3(1)T

Cisco IOS Release 11.3(1)T or later release of Cisco IOS Release 11.3 T

8 MB

Cisco IOS Release 11.3(1)

Cisco IOS Release 11.3(1) or later release of Cisco IOS Release 11.3

8 MB

Cisco IOS Release 12.0(1)T

Cisco IOS Release 12.0(1)T or later release of Cisco IOS Release 12.0T

8 MB

Cisco IOS Release 12.0(1)

Cisco IOS Release 12.0(1) or later release of Cisco IOS Release 12.0

8 MB

Cisco IOS Release 12.0(2)XE3

Cisco IOS Release 12.0(2)XE3 or later release of Cisco IOS Release
12.0 XE3

8 MB

Cisco IOS Release 12.0(4)XE1

Cisco IOS Release 12.0(4)XE1 or later release of Cisco IOS Release
12.0 XE1

8 MB

Cisco IOS Release 12.0(5)S

Cisco IOS Release 12.0(5)S or later release of Cisco IOS Release 12.0 S

8 MB

Cisco IOS Release 12.1(1)E

Cisco IOS Release 12.1(1)E or later release of Cisco IOS Release 12.1 E

8 MB

Cisco IOS Release 12.1(1)

Cisco IOS Release 12.1(1) or later release of Cisco IOS Release 12.1

8 MB

Cisco IOS Release 12.1(5)T

Cisco IOS Release 12.1(5)T or later release of Cisco IOS Release 12.1 T

16 MB

Summary of Contents for RSP4+





















Reviews: