background image

Statement 1071

Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner
des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des
dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes
de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin
de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Attention

Statement 1004

Installation Instructions

Warning

Read the installation instructions before connecting the system to the power source.

Warning

Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.

Attention

Statement 1074

Comply with Local and National Electrical Codes

Warning

Installation of the equipment must comply with local and national electrical codes.

Warning

L'équipement doit être installé conformément aux normes électriques nationales et locales.

Attention

8

Summary of Contents for USC 5030













Reviews: