background image

 

3-2

Cisco VG202 and Cisco VG204 Voice Gateways Hardware Installation Guide

OL-15959-01

Chapter 3      Installing Cisco VG202 and Cisco VG204 Voice Gateways

  Safety Recommendations

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity. 

Statement 1001

Warning

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. 
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The 
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) 
while the housing is open, or both. 

Statement 1043

General Safety Practices

Follow these guidelines to ensure personal safety and protect the equipment:

  •

Keep the chassis area clear and dust-free during and after installation.

  •

Put the removed chassis cover in a safe place. 

  •

Keep tools away from walk areas where you and others could fall over them. 

  •

Do not wear loose clothing that could get caught in the chassis. 

  •

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Safety Tips

Use these tips as safety guidelines when installing or working around this equipment:

  •

Locate the emergency power-off switch for the room in which you are working. Then, if an electrical 
accident occurs, you can act quickly to turn off the power.

  •

Disconnect all power before installing or removing a chassis.

  •

Do not work alone if potentially hazardous conditions exist. 

  •

Never assume that power is disconnected from a circuit. Always check. 

  •

Look carefully for possible hazards in your work area, such as moist floors, ungrounded power 
extension cables, and missing safety grounds. 

  •

If an electrical accident occurs, proceed as follows:

  –

Use caution; do not become a victim yourself.

  –

Turn off power to the system.

  –

If possible, send another person to get medical aid. Otherwise, assess the condition of the victim 
and then call for help.

  –

Determine if the person needs rescue breathing or external cardiac compressions; then take 
appropriate action. 

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD occurs when 
electronic components are improperly handled; it can result in complete or intermittent failures. 

Summary of Contents for VG202



















































Reviews: