background image

6. TROUBLESHOOTING

7.SPECIFICATION

1. Turn on the receiver, but the indicator does not light.

-Make sure the power cable is well fixed and the socket is in good condition.
-Check if the fuse is blown.

2. When you speak, the "AF" light twinkles but no sound output.

-Check if the volume is in lowest place or the audio cable is not fixed well.

3. The effective signal-receiving distance becomes close. And signal-receiving

is not well. Sound quality is bad.

-Check if the battery power is low. Change new battery.
-Check if there are same frequency signals in your surroundings.

* Do not use two units with the same frequency at the same time in a place.

(Separate them at least 120m.)

* Do not open and repair it when some serious breakdown happens.
* Please contact your local distributor for repair.

1.COMPREHENSIVE PERFORMANCE

2.RECEIVER

POWER SUPPLY:

DC15V

CONSUME POWER:

5 WATER

SIGNAL/NOISE RATIO:

MORE THAN 90dB

IMAGE & SPURIOUS REJECTION:

MORE THAN 80dB

BORDER UPON CHANNEL REJECTION: MORE THAN 80dB
RECEIVING SENSITIVITY:

LESS THAN 10dBu V(SINAD=30dB)

DE-EMPHASIS:

50

µ

s

CARRIER FREQUENCY:

UHF 863-865MHz

FREQUENCY STABILISATION:

< 30ppm

DYNAMIC RANGE:

MORE THAN 90dB

TOTAL HARMONIC DISTORTION:

LESS THAN 0.5%

FREQUENCY RESPONSE:

40HZ-15KHZ 3dB

AUDIO OUTPUT LEVEL:

UNBALANCED OUT: 0-- 400mV

BALANCED OUT: 0-- 200mV

Summary of Contents for MP16UHF








Reviews: