background image

 

ii 

 

 

 

CAUTION 

RISK OF ELECTRIC SHOCK DO NOT OPEN 

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, 

DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE 

PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

 

 

 

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the 
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may 
be of sufficient magnitude to constitute a risk of electric shock to persons. 

 

The exclamation point within an equilateral triangle is intended to alert the user to the presence 
of important operating and maintenance (servicing) instructions in the literature accompanying 
the product. 

 

 

IMPORTANT SAFETY INSTRUCTIONS 

READ BEFORE OPERATING EQUIPMENT 

This product was designed and manufactured to meet strict quality and safety standards. 

There are, however, some installation and operation precautions which you should be particularly aware of. 

1.

 

Read these instructions. 

2.

 

Keep these instructions. 

3.

 

Heed all warnings. 

4.

 

Follow all instructions. 

5.

 

Do not use this apparatus near water. 

6.

 

Clean only with dry cloth. 

7.

 

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 

8.

 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce 
heat. 

9.

 

Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into 
your outlet, consult an electrician for replacement of the outlet. 

10.

 

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus. 

11.

 

Only use attachments/accessories specified by the manufacturer. 

12.

 

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. 

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 

13.

 

Unplug this apparatus during lightning storms. 

14.

 

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in 
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the 

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 

 

 

Summary of Contents for CG800 Series






















Reviews: