background image

11

To re-enter the vehicle and resume driver control:
1.  Disarm the alarm by pressing Button 2 on the Remote Transmitter.*

•  The doors will unlock.*

2.  Turn on the ignition.
3.  Press the brake pedal to disengaged the MS2005.

•  The LED will turn off.

*If optional keyless entry feature is installed.

5.4 Auto Cold Starting 

The Auto Cold Starting Feature automatically starts the vehicle every two hours and
runs for the preset Run Time. 
To enter Cold Start Mode:
1. Be sure ignition is off.
2. Press and hold the Valet switch.
3. Continue holding the Valet switch and press Transmitter Button 3 for 5 seconds

then release both buttons.

•  The parking lights will flash 5 times.
• The engine will start and run for 30 seconds then shut down.
• The LED will double flash.

6. LCD 2-way Transmitter (MS2107)

6.1 Programming LCD 2-way Remote Transmitters

Make sure to have the transmitter ready and follow the steps below.  
To program a transmitter:
1. Turn the ignition ON.
2. Press the Valet/Override switch twice and hold for 5 seconds.

• The siren will chirp once.

3. Press and hold the Lock button on the LCD transmitter for 2 seconds.

• The siren will chirp once.
• The LCD transmitter will beep.

4. Turn OFF the ignition when transmitter programming is complete.

• The siren will chirp 3 times.

MS2105 owner.qxd  8/25/2003  4:21 PM  Page 11

Summary of Contents for UNGO MS2105

















Reviews: