background image

3

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS

IMPORTANT: Make sure that you 
wear protective clothing, gloves, 
goggles, face mask as 
appropriate for the fluid being 
extracted.

1. Keep the extractor clean and 

maintain it in good condition.

2. Replace or repair damaged 

parts. Use genuine CLARKE parts 
only. Unauthorised parts may be 
dangerous and will invalidate the 
warranty.

3. Check extractor connections 

and fittings before use. Check 
that there are no leaks.

4. Ensure that the extractors tank 

capacity exceeds the amount of 
fluid to be collected.

5. Make sure that the end of the 

suction tube is fully submerged in 
the fluid before operating.

6. When not in use, store in a safe, 

dry, childproof area.

7. Keep the work area clean, 

uncluttered and ensure there is 
adequate lighting.

8. Maintain correct balance and 

footing. Ensure the floor is not 
slippery and wear non-slip shoes.

9. Keep children and unauthorised 

persons away from the working 
area.

10. Dispose of waste fluids in 

accordance with local authority 
regulations. 

DO NOT ALLOW 

UNCONTROLLED DISCHARGE OF 
FLUIDS, THUS POLLUTING THE 
ENVIRONMENT.

11. DO NOT pull or yank any pipes or 

hoses and do not attempt to 
move the extractor by pulling the 
hose.

12. Use only to extract engine or 

transmission oils, or similar NON-
corrosive fluids. The unit may also 
be used for the transfer of water.

13. DO NOT use to extract hazardous 

or harmful chemicals, solvents, 
petrol, diesel, kerosene, alkaline 
or acids. If such fluids are used in 
the unit, it must be immediately 
drained and thoroughly cleaned. 
Use with prohibited fluids will 
invalidate your warranty.

14. DO NOT store fluids in the 

extractor. Fluids must be emptied 
into an approved receptacle as 
soon as possible.

15. DO NOT dismantle, tamper or 

adapt the extractor for any 
purpose other than for which it is 
designed.

16. DO NOT store in areas of high 

temperature, direct sunlight, rain 
or snow.

WARNING: MAKE SURE THAT HEALTH & SAFETY, LOCAL AUTHORITY, AND 
GENERAL WORKSHOP PRACTICE REGULATIONS ARE STRICTLY ADHERED 
TO WHEN USING THIS EQUIPMENT.

Summary of Contents for 1801928













Reviews: