Clarke 3110472 Operating & Maintenance Instructions Download | Manualshive

Page: 15 / 16

background image

15

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

«
...
13
14
15
16
»

Summary of Contents for 3110472

















Reviews:

No comments

Related manuals for 3110472

Brand: Jet Pages: 12

Brand: Makita Pages: 17

Brand: Balcrank Pages: 8

Brand: BGS technic Pages: 9

Brand: Mannesmann Demag Pages: 16

Brand: KNIPEX Pages: 12

Brand: Ryobi Pages: 15

Brand: Wacker Neuson Pages: 36

Brand: Felder Pages: 10

Akku-Press 22 V ACC

Brand: REMS Pages: 212

TJEP KA 4060 GAS 3G

Brand: Kyocera Pages: 8

Brand: Jefferson Pages: 4

Brand: Bullet tools Pages: 10

Brand: Milwaukee Pages: 55

CC150MOB Series

Brand: Custom Crimp Pages: 15

Brand: Uniflex Pages: 44

Brand: Central Machinery Pages: 16

Brand: WORKERS BEST Pages: 159

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands