background image

4

GENERAL SAFETY RULES 

WORK AREA

1. Keep the work area clean and well lit. Cluttered and dark areas invite 

accidents.

2.

DO NOT

 not operate log splitters in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust. Log splitters can create 
sparks which may ignite the dust or fumes.

3.

DO NOT

 not operate this log splitter in enclosed or confined spaces as the 

engine will give off harmful exhaust fumes.

4. Keep children and bystanders away while operating the log splitter. 

Distractions can cause you to lose control.

5. The surface must be perfectly level to prevent the machine from moving 

during operation.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common sense when 

operating a log splitter. 

DO NOT

 use the log splitter while you are tired or 

under the influence of drugs, alcohol or medication. A moment of 
inattention while operating log splitters may result in serious personal injury. 

2. Use safety equipment. 

ALWAYS

 wear eye and ear protection. Safety 

equipment such as non-skid safety shoes, close fitting clothing and suitable 
work gloves should always be used.

3.

DO NOT

 overreach. Keep proper footing and balance at all times. This 

enables better control of the log splitter in unexpected situations. 

4. Dress properly. 

DO NOT

 wear loose clothing or jewellery. Keep your hair, 

clothing and gloves away from moving parts. Loose clothes, jewellery or 
long hair can be caught in moving parts. 

USAGE AND CARE

1.

DO NOT

 force the log splitter. It will do the job better and safer at the rate 

for which it was designed.

2. Store the log splitter out of the reach of children and 

DO NOT 

allow persons 

unfamiliar with log splitters or these instructions to operate the log splitter. 
Log splitters are dangerous in the hands of untrained users.

WARNING: READ ALL OF THESE INSTRUCTIONS. FAILURE TO FOLLOW ALL 
INSTRUCTIONS LISTED BELOW MAY RESULT IN FIRE AND/OR SERIOUS 
INJURY. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. 

Summary of Contents for 3402041

























Reviews: