background image

15

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DISASSEMBLY

When disassembling the garage 
depress the spring-loaded bar to 
disengage the ratchet and open the 
ratchet handle completely to allow 
the webbing strap to pull through.

PLEASE RE-READ ALL WARNINGS 
CONTAINED ON PAGE 2/3 OF THESE 
INSTRUCTIONS. SAVE THESE 
INSTRUCTIONS FOR FUTURE USE.

To dismantle, execute all instructions 
in reverse order. Store your garage in a cool, dry location between seasons to 
prolong the usable life of all components.

Components are not equally durable and will require replacement over time 
at differing intervals.

ADDITIONAL ANCHORING

Please note that when the instant garage or shed is to be sited on soft ground 
an additional, or alternative method of anchoring may be required.

This can take the form of an additional Auger Securing Set GA1 (already 
supplied with Clarke instant garages), which can add greater security for 
exposed, windy locations.

Alternatively the Easy Hook Anchoring System GHA2, can be used to provide 
greater security on soft ground.

 

Available from your Clarke dealer.

WARNING: SERIOUS INJURY TO PERSONS OR PROPERTY COULD RESULT IF 
THE GARAGE IS NOT SECURELY ANCHORED.

Summary of Contents for 3503576

















Reviews: