7/2014
A - 13
56091130 - CA30 20B
ENGLISH - A
INSTRUCTIONS FOR USE
RECOVERY TANK EMPTYING
Turn off the machine.
1.
Raise the squeegee assembly (14).
2.
Move the machine to a dedicated draining location.
3.
Grasp the handle (2) and tilt the machine backward until the guide wheel touches the
fl
oor.
4.
Remove the drain hose from the clip, bend the top end of draining hose (A, Figure 13), and
5.
then remove the drain hose cap. Lower the hose to a low level or on the ground to drain the
water. Alternatively, place drain hose to a low position or on the ground to make the water
outlet face downward (B, Figure 13), and then twist open the drain cap to drain the wastewater
in the tank. After draining is completed, rinse the inside of recovery tank with clean water
CAUTION !
When draining the wastewater, the drain hose must be folded or lowered to a lower
position (Figure 13 A or B), and the cap removed for wastewater to drain. Do not allow the
opening of the drain hose to face upward, as it could get wastewater on the operator..
SOLUTION TANK EMPTYING
Complete Steps 1 to 4.
6.
As shown in Figure 14, turn open the lid of Solution tank (A) counter clockwise (direction C), to
7.
drain Solution tank completely. Use clean water to rinse the inside of Solution tank. When work
is completed, replace the solution tank lid (A) by twisting in a clockwise in direction (B).
AFTER EACH USE
When work is done and before leaving the machine, completes the following steps:
Remove the brush / pad holder.
1.
Drain solution tank & rinse with clean water.
2.
Drain recovery tank & rinse with clean water.
3.
Complete the daily maintenance procedures. (see maintenance section)
4.
Remove and rinse squeegee assembly with damp towel.
5.
Keep recovery tank lid unsealed from tank to allow fresh air to circulate freely
6.
PERIODS OF INACTIVITY
If the machine is not to be used for more than 30 days, please treat it in the following way:
Complete the necessary procedure that should be followed after the machine is used.
1.
Disconnect the connector (9) connecting the battery and the machine.
2.
In order not to damage the batteries, the batteries should be charged once every 3 months.
3.
USING FOR THE FIRST TIME
After the
fi
rst 9 hours of use, please check components to ensure all connections (electrical & mechanical) are tight & check for any damage that
may have occurred during operation. Check for water leakage.
B
A
A
A
C
B
FIGURE 13
FIGURE 14
Summary of Contents for 510B
