background image

 Thank you for purchasing this CLARKE Sander/Polisher, which is designed for DIY use.

Before attempting to use the machine, please read this manual thoroughly and follow
the instructions carefully. In doing so you will ensure the safety of yourself and that of
others around you, and you can look forward to the product giving you long and
satisfactory service.

Guarantee

This product is guaranteed against faulty manufacture for a period of 12 months from the
date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in
any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to
us without prior permission.
This guarantee does not effect your statutory rights.

Specifications

Elec. Supply .................................................

230V 50Hz 1 ph

Power Rating ..............................................

1300W  Motor

Fuse  Rating ..................................................

13amp

No Load Speed ..........................................

1,000-3,000 RPM

Sound Power Level ....................................

98.1dB(A)

Net Weight ..................................................

5.0 kg

Spindle Thread ...........................................

M14

Vibration
Measured vibration emission value -

 a: .

<

2.5m/s

2

Highest reading in a single plane ...............

5.1m/s

2

Values determined according to EN28622-1

Residual Risks

Even when the power tool is used as prescribed it is not possible to eliminate all
residual risk factors. The following hazards may arise in connection with the power
tool’s construction and design:

1.

Damage to lungs if an effective dust mask is not worn.

2.

Damage to hearing if effective hearing protection is not worn.

3.

Damages to health resulting from vibration emission

if the power tool is being used over longer period of time or not adequately
managed and properly maintained.

WARNING! This machine produces an electromagnetic field during operation. This
field may under some circumstances interfere with active or passive medical
implants. To reduce the risk of serious or fatal injury, we recommend persons with
medical implants to consult their physician and the medical implants manufacturer
before operating this machine.

Environmental Protection

Do not dispose of this product with general household waste. All tools,
acessories and packaging should be sorted, taken to a re-cycling centre
and disposed of according to the laws governing Waste Electrical and
Electronic Equipment.

-2-

Summary of Contents for 6462105













Reviews: