A-12
- FORM NO. - 56091028 - FOCUS
®
II LARGE
A-12 / ENGLISH
WET SCRUBBING
WARNING!
Be sure you understand the operator controls and their functions. While on ramps or inclines, avoid sudden stops when loaded.
Avoid abrupt sharp turns. Use low speed down hills. Clean only while ascending (driving up) the ramp.
1
Follow the instructions in the Preparing the Machine For Use section of this manual.
2
Turn the Master Key Switch
(A)
ON (I). This will display the control panel indicator lights, reference the Battery Indicator and Hour Meter on the Display
(J)
.
3
To transport the machine to the work area, push either of the Palm Buttons
(29)
to go forward or press either Palm Button
(29)
and the Reverse Button
(28)
to move the machine in reverse.
NOTE:
Speed Control Knob
(30)
is used to control the maximum speed in either forward or reverse.
4
Press and hold the Solution Switch
(B)
for 5 seconds to pre-wet the
fl
oor.
NOTE:
This must be done prior to pressing the Scrub ON Switch
(I)
.
5
Press the Scrub ON Switch
(I)
once for Regular Scrub Pressure or twice for Heavy Scrub Pressure mode. Hold this switch for 5 seconds for Extreme Scrub
Pressure mode. Once the scrub system is activated, pressing the Solution Switch
(B)
will toggle between solution off, low, medium and high solution
fl
ow
rates.
NOTE:
The solution and vacuum systems are automatically activated when the Scrub ON Switch
(I)
is pressed. No further action is required other than
lowering the squeegee
(17)
. Any individual system can be turned OFF or back ON by simply pressing its switch at any time during scrubbing.
6
Lower the squeegee with the Squeegee Raise / Lower Lever
(17)
.
7
When the Palm Buttons
(29)
are not being pressed (machine stationary), the scrub, vacuum and solution systems are activated but not running. Grip the
Operator Control Handle
(2)
and press either of the Palm Buttons
(29)
to start the scrub, vacuum and solution, and to move the machine forward. For best
results, move the machine at a slow walking speed. Press either palm button and the reverse button to move the machine in reverse. The brushes will run
while moving the machine in reverse, but solution will not be dispensed.
CAUTION!
To avoid damaging the
fl
oor, keep the machine moving while the brushes are turning.
8
When scrubbing, check behind the machine occasionally to see that all of the waste water is being picked up. If there is water trailing the machine, you may
be dispensing too much solution, the recovery tank may be full, or the squeegee tool may require adjustment.
9
For extremely dirty
fl
oors, a one-pass scrubbing operation may not be satisfactory and a “double-scrub” operation may be required. This operation is the
same as a one-pass scrubbing except on the
fi
rst pass the squeegee is in the up position. This allows the cleaning solution to remain on the
fl
oor to work
longer. The
fi
nal pass is made over the same area, with the squeegee lowered to pick up the accumulated solution.
10 The recovery tank has an automatic shut-off switch that turns ALL systems OFF except the drive system when the recovery tank is full. When this switch is
activated, the recovery tank must be emptied. The machine will not pick up water or scrub with the switch activated.
NOTE:
The Hour Meter
(J2)
momentarily
fl
ashes each letter of the word FULL over and over.
11 When the operator wants to stop scrubbing or the recovery tank is full, press the Scrub OFF Switch
(H)
once. This will automatically stop the scrub brushes
and solution
fl
ow and the scrub deck will raise UP.
NOTE:
The vacuum will stop after a 10 second delay. This is to allow any remaining water to be picked up
without turning the vacuum back on.
12 Raise the squeegee and drive the machine to a designated wastewater “DISPOSAL SITE” and empty the recovery tank. To empty, pull the Recovery Tank
Drain Hose
(27)
from its hanger and open the cap (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled
fl
ow of waste
water). The Recovery Tank Drain Hose
(27)
can be squeezed to regulate the
fl
ow. Re
fi
ll the solution tank and continue scrubbing.
NOTE:
Make sure the Recovery Tank Cover
(5)
and the Recovery Tank Drain Hose
(27)
cap is properly seated or the machine will not pick-up water correctly.
When the batteries require recharging the Battery Indicator
(J1)
will
fl
ash red and the vacuum motor will shut off after 30 seconds. Transport the machine to a
service area and recharge the batteries according to the instructions in the Battery section of this manual.
SERVICE NOTE: Refer to the service manual for detailed functional descriptions of all controls and optional programmability.
