Clarke PHT3 Operating & Maintenance Manual Download | Manualshive

Page: 7 / 12

background image

7

8

9

11

10

Lower Top Cover over Stack

Attach Gas Delivery Pipe to the Burner
Assembly, ensuring it is perfectly tight.

NOTE: USE TWO SPANNERS AS SHOWN.

Insert Gas Delivery Pipe into Stack

Secure Burner Assembly to Stack.

3xScrews M6x12

3x Flat Washers

NOTE: Test the joint for leaks by applying a soapy liquid
to the joint. If bubbles appear, tighten the nut. The joint
must be gas tight.

«
...
5
6
7
8
9
...
»

Summary of Contents for PHT3













Reviews:

No comments

Related manuals for PHT3

Brand: Celsius Pages: 4

Platinum GHOR900

Brand: Goldair Pages: 16

Brand: Olimpia splendid Pages: 104

BTR(C)120 THRU 500A

Brand: A.O. Smith Pages: 36

Brand: Mr. Heater Pages: 28

Brand: Nibe Pages: 56

Fillcontrol Auto Compact

Brand: Reflex Pages: 17

Brand: Lumme Pages: 10

Brand: Zephir Pages: 29

Copper Cricket 1B

Brand: Sage Advance Corp Pages: 67

Brand: Napoleon Pages: 15

Klimatronic Heat Safe humid 1000

Brand: SUNTEC Pages: 100

Brand: Totai Pages: 2

Brand: Quietside Pages: 44

Brand: STIEBEL ELTRON Pages: 20

Brand: Truma Pages: 2

Brand: VALBERG Pages: 36

Brand: STIEBEL ELTRON Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands