background image

6

TROUBLE SHOOTING

If the system is set up properly, there is little likelihood of problems arising, but if
water will not flow as it should then check the following points:-

1.

If using a suction lift, the suction hose and connections need to be completely
air tight, otherwise air will be drawn in and either reduce or completely stop
the flow of water.

Additionally, ensure that the system has been fully primed with water up to
the top lip of the outlet port adapter.

2.

Check to see that no foreign matter is fouling the intake system - check the
strainer is not blocked or obstructed.

Should you still experience problems, then contact your Clarke dealer, or CLARKE
International Service Department for advice.

Please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL:  020 8988 7400

PARTS & SERVICE FAX:  020 8558 3622

or    e-mail as follows:

PARTS:   Parts@clarkeinternational.com

SERVICE:    Service@clarkeinternational.com

ACCESSORIES

Foot Valve Filter Brass ....................................................................... 7950561

1” I.D. Reinforced Hose for suction and delivery. ......................... 7955010

Water Filter ......................................................................................... 7175100

Water Filter cartridge ........................................................................ LDCF10

SPARE PARTS & SERVICING

Summary of Contents for SPP3










Reviews: