GREAT BRITAIN
For consumer contact, please visit www.clasohlson.co.uk and click on customer service. Internet: www.clasohlson.co.uk
d
e
a
b
c
Ver
. 00
1-200
708
Stopwatch
Art.no: 31-4141 • Model: 100MT
Please read the entire instruction manual before using and save it for
future use.
Product Description
- Stopwatch to max. 23 hours, 59 minutes and 59 seconds with 1/100
seconds precision, split time and sound signal with lap-time records.
- Memory for lap-times, split times, finishing times, quickest lap and
average time.
- Pulse clock from 50 to 240 beats/minute. The user can set age, gender
and high/low limit. The pulse indicator reads data from the finger.
- Display of time, date and day.
- Automatic year digit from 2005 to 2035.
- Two time zones.
- 12 or 24 hour display.
- Alarm with possibility for two alarm settings.
- Hour signal.
- Pace keeper, adjustable from 10 to 240 signals/minute.
Battery
The stopwatch operates on 1x 3 V CR2032 battery. For change of battery,
open the battery compartment on the back of the stopwatch by twisting
open the flap with e.g. a coin. Remove the old battery and insert a new
one. Make sure that the plus pole is placed upward.
Stopwatch
7) Now you can press Store (a) to start the timekeeping again, or press
Start/Stop (c) to stop the timekeeping.
8) If you would like to store the data from the stopwatch, hold in Start/
stop for 2 seconds. STORE DATA is displayed.
9) If you would like to erase the data, hold in Adjust (d) for two seconds.
CLEAR DATA blinks while you hold in the button. Note that all
stored data in the stopwatch is erased.
Storing and using data
a) Store
b) Mode
c) Start/Stop
d) Adjust
e) Sensor for pulse indicator
1) Press Mode (b) once or several
times until the display shows
CHRO for approx. one second and
then changes to the following:
2) Start the timekeeping by pressing
Start/stop (c). The display shows
minutes, seconds and 1/100. If the
timekeeping exceeds 1 hour, the
number of hours are given in the
upper part of the display.
3) In the display’s upper left corner the number of laps are shown. The
upper part of the display shows lap-times and the lower part shows
split times.
Split time refers to the time it takes to travel from start to a given
point along the track.
Lap-Time refers to the time it takes to travel a given distance within
the total distance.
4) Every time you finish a lap press
Store (a) to save the time. This
time blinks in the upper part of the
display for 2 seconds at the same
time as the current time shows
continuously in the lower part of
the display. Every time you set a
lap record FASTEST blinks at the
same time as a signal sounds.
5) The upper part of the display resumes to showing the time for the
next lap. The amount of laps are updated as well. The lower part of
the display continues to run time.
6) Press Start/stop (c) to stop the timekeeping. PAUSE is shown on the
display. The total time and remaining laps are shown in alternate
blinking.
- To retrieve stored data from the stopwatch press Store (a) to browse
the lap you would like to look at. Then press Start/stop (c) to see the
lap you have chosen.
- Press Start/stop (c) to browse to the laps. The sequence is: Individual
lap-time – total time – best lap time – average lap-time.
Time, date and day
Setting
1. Press Mode (b) once or several times to move to normal time mode.
Time is shown for 0.5 seconds before the display shows normal time
mode.
2. Hold in Adjust (d) for 2 seconds to move to the setting mode. The
digit for time zone starts to blink. Press Start/stop (c) to switch
between the time zones and confirm with Mode (b).
3. The time indicator starts to blink. Press Start/stop (c) to increase the
value and press Store (a) to decrease. Increase or decrease the value
quickly by holding in the respective button. Confirm the setting by
pressing Mode.
4. The minute indicator starts to blink. Press Start/stop (c) to increase
the value and press Store (a) to decrease. Increase or decrease the
value quickly by holding in the respective button. Confirm the setting
by pressing Mode.
5. The seconds indicator starts to blink. Press Start/stop (c) or Store (a)
to reset the value to zero.
6. The month indicator starts to blink. Press Start/stop (c) to increase the
value and press Store (a) to decrease. Increase or decrease the value
quickly by holding in the respective button. Confirm the setting by
pressing Mode.
