GREAT BRITAIN
For consumer contact, please visit www.clasohlson.co.uk and click on customer service. Internet: www.clasohlson.co.uk
Wireless Doorbell
Article number: 36-1725, model: SC329D
•
Wireless doorbell with belt clip.
•
Including transmitter and receiver.
•
Several different signals.
•
Range about 25 metres.
•
Operated on one CR2032 (included) and two LR6 (not included).
Please read the entire instruction manual before using and save it for
future use. We apologise for any text or photo errors and any changes of
technical data. If you have any questions concerning technical problems
please contact our Customer Service Department.
Inserting Batteries
Push button (transmitter) operates on one Lithium battery (CR2032, 3V)
that is included. Battery is mounted and the product is ready to use when
delivered.
How to change battery when needed:
Loosen the push buttons back-
side carefully using a screwdriver. Loosen the screw for the battery
attachment (the shackle) place the battery with the (+) against the battery
attachment (the shackle) tighten the screw and put back the backside.
The doorbell (receiver) operates on 2x LR6 batteries (not included).
1. Remove the battery cover on the back.
2. Insert 2x LR6 batteries according to the markings on the battery
compartment.
3. The buzzer sounds twice to indicate that it is ready to use and to
read the radio frequency from the push button (see chapter Setting
of radio frequency).
4. Close the battery cover.
Mounting
Find a suitable location and test the signal range before drilling the holes.
Push button (transmitter)
Loosen the push buttons backside carefully using a screwdriver. Use the
two holes on the backside as template and mark desired location close
by the door. Drill two holes and mount the push button with the supplied
screws (use plugs if needed) or double-sided adhesive tape (included).
Note!
Do not mount the push button on a metal surface; it will reduce the
range considerably.
Doorbell (receiver)
Hang it up in the belt clip or use the hole for hanging underneath the belt
clip. Mount a screw where the doorbell is to be hang, leave about 3 mm
between the wall and screwhead.
Signal selection
Set the signal underneath the backside of the push button. With a button
marked S. Westminster is preset, press the button to change to the next
and then the next etc. Switch between 8 different melodies and sounds.
Note!
You can purchase an additional push button and use it by the
backdoor etc. Set it on a different signal then the first to know which door
your visitor is ringing from.
Setting of radio frequency
The wireless doorbell is set on a radio frequency from the factory, change
frequency if disturbance occur from other units in the neighbourhood.
The push buttons radio frequency can be changed by the shackle on
the backside and the doorbell (receiver) sets the correct radio frequency
automatically. No need to manually changing it.
Change the push buttons radio frequency like this:
1. Loosen the push buttons backside carefully using a screwdriver.
2. There are frequency settings with four different shackles (1, 2, 3, 4)
that together gives 16 different settings.
3. Change the setting by removing one or more shackles. Remove the
batteries from the doorbell (receiver) and put them back again. The
buzzer sounds twice to indicate that it is ready to read the new radio
frequency.
4. Press the push button after changing a setting and put back the
batteries. The doorbell will sound and indicates therefore that it is
controlled by the set frequency on the push button and saves it in the
memory.
5. Testing the function.
Function
Press the push button once and it will send a wireless signal to the door-
bell. The doorbell will sound and the LED lights up once and stops when
the set signal ends. The signal is not repeated unless you hold in the push
button, release the push button and press again if you wish to repeat the
signal.
Volume control
The volume setting is in the doorbells battery compartment.
LO
low –
HI
high
Note! Helpful Suggestions:
-
Do not mount the push button on a metal frame etc. test the function/
location before the final mounting.
-
Do not expose the push button or receiver to water or extreme heat.
-
Do not mix new/old batteries or different types of batteries. Remove
the batteries if the product is not to be used for a longer period of time
(to avoid leakage).
-
Use alkaline batteries in the doorbell that will last long, remove used
batteries to avoid leakage.
Warning!
Use only batteries of recommended type placing them correctly
according to the (+) and (-) marking.
Troubleshooting
No sound but the LED blinks when the push button is pressed in
:
-
The distance is too far between the units: change location!
-
Units are set on different radio frequency: control the shackle on all
units!
No sound and no indication from the LED when the push button is
pressed in:
-
Bad battery in the push button: change battery!
-
Battery is placed incorrectly in the push button: place the battery
correctly (+ outwards)!
The doorbell sounds without the push button being pressed in:
-
Wireless products in the surrounding area affect the doorbell: change
frequency (see above)!
Specifications
Push button (transmitter)
:
Battery:
CR2032 Lithium (3V)
Current Consumption:
3.0mA (while transmitting)
0.003mA (in standby mode)
Doorbell (receiverp)
Battery:
2x LR6
Current Consumption:
100mA (while receiving)
0. 3mA (in standby mode)
Operating temperature: -10°C to +40°C
Range:
Up to 25 metres (outdoor, unobstructed area)
Sound:
8 different sounds
Frequency settings:
16 different options.
Size:
94x61x30 mm (doorbell)
85x33x26 mm (push button)
Disposal
Follow local ordinances when disposing of this product. If you are unsure
about how to dispose of this product contact your municipality.
ENGLISH
