EQ 3100
AUTOMATIC WHEEL BALANCER 3D VIDEO LASER POINTER
79
The Error signal is always accompanied by a triple beep indicating that the machine cannot run the command given by the
operator, or, during operation, conditions were encountered that prevent the action in progress from continuing.
The machine reports error conditions by displaying an outline of the description of the cause of the error. The list of error codes and
description outlines is provided in table.
ERROR CODES
Error code
Description
Notes
000 to 009
Machine parameters internal error.
Contact technical support.
010
Reverse rotation of the wheel.
Contact technical support.
012
The wheel cannot be stopped at the end of the launch.
Check the mains voltage. If the checks do not lead to any results, contact technical
support.
014
The wheel does not spin.
Contact technical support.
015
Keypad blocked at start-up.
Release all buttons, then turn off or restart the machine. If the error persists, contact
technical support.
016
Distance sensor is not in rest position at start-up of the
machine or when Start is pressed.
Place the sensor back in its rest position: the error should disappear. If the error
persists, contact technical support.
NOTE: if key [P5] is pressed the machine acquisition system is temporarily disabled
and operation can be continued. The disabled status will last until the machine has
been turned off.
017
Width sensor is not in rest position at start-up of the ma-
chine or when Start is pressed.
Place the sensor back in its rest position: the error should disappear. If the error
persists, contact technical support.
NOTE: if key [P5] is pressed the machine acquisition system is temporarily disabled
and operation can be continued. The disabled status will last until the machine has
been turned off.
019
Communication processor failure.
Turn the machine off and then on again. If the error persists, contact technical
support.
The machine can still be used but all functions related to the USB port are disabled.
The machine can still be used but all functions related to the USB port are disabled.
020
Lack of communication with the eeprom memory.
Turn the machine off and then on again. If the error persists, contact technical
support.
021
Lack of machine calibration data or incorrect calibration
data.
Carry out calibration for the CAR/SUV Wheel Type and/or for the MOTO Wheel
Type. If the error persists, contact technical support.
See also ERR 030 and ERR 031.
022 to 024
Error during calibration.
Excessive imbalance or anomaly. Turn the machine off and then on again. If the error
persists, contact technical support.
025
Presence of weight during the Cal0 calibration phase.
Remove the weight and repeat the launch of the Cal0 phase. If the error persists,
contact technical support.
026
A launch without weight or failure of the pick-up A signal
in the Cal2 calibration phase.
Apply the intended weight and repeat the launch. If the error persists, contact techni-
cal support.
027
A launch without weight or failure of the pick-up B signal
in the Cal2 calibration phase.
Apply the intended weight and repeat the launch. If the error persists, contact techni-
cal support.
028
Launch with weight on the internal side during the Cal3
calibration phase. In this phase, the weight must be on the
external side.
Remove the weight from the internal side and repeat the launch. If the error persists,
contact technical support.
030
Lack of calibration data for the CAR/SUV Wheel Type.
Carry out calibration for the CAR/SUV Wheel Type.
031
Lack of calibration data for the MOTO (motorbike) Wheel
Type.
Carry out machine calibration for the MOTO Wheel Type.
034
The MOTO Wheel Type is activated: a different Program
Type other than ALU1 cannot be used.
Other Program Types cannot be selected.
039
The wheel guard is open: the requested action cannot be
performed.
Summary of Contents for EQ 3100
Page 52: ...EQ 3100 AUTOMATIC WHEEL BALANCER 3D VIDEO DISPLAY LASER POINTER 52...
Page 53: ...EQ 3100 AUTOMATIC WHEEL BALANCER 3D VIDEO DISPLAY LASER POINTER 53...
Page 67: ...EQ 3100 AUTOMATIC WHEEL BALANCER 3D VIDEO DISPLAY LASER POINTER 67...
Page 69: ...EQ 3100 AUTOMATIC WHEEL BALANCER 3D VIDEO DISPLAY LASER POINTER 69...
