background image

22

Using the CP-800

The CP-800’s versatile touchscreen LCD supports your day-to-day operations 

and provides access to a flexible menu system for controls and setup functions 

that aren’t accessed as often. This section of the owner’s manual outlines the use 

of the touchscreen in routine operation of the system.

When you bring the CP-800 out of 

Standby 

mode, the touchscreen displays the 

Home page of the menu system, as shown below.

The 

Home

 page displays the volume in large font which is easily visible from 

across a room. The selected source appears at the bottom of the screen. At the 

bottom center of the screen the format of the incoming signal is displayed. 

This displays the sampling frequency of digital sources as well as the file format 

(ALAC, WAV, FLAC, etc.) of streaming Network sources or Bypass if so selected 

for analog sources. If Pass-Thru is selected for either digital or analog sources, 

the volume display will read 0.0 and be greyed out (since the volume control 

is not active in this mode). This  page can be quickly accessed at any time by 

pressing the 

Home

 button on the remote control or tapping the home icon on 

the touchscreen display. 

Source Selection

Touching the screen when on the Home page brings up the Source Selection 

page. The number of source buttons appearing here corresponds to the number 

of inputs that have been set up and are “enabled.” A maximum of nine sources 

may appear on one page. If more are enabled, they will be available on the next 

page by touching the 

 button in the upper right corner of the page. See the 

section on source setup in the Menu System. The CP-800 has up to 18 selectable 

source buttons which are all interchangeable. 

Summary of Contents for CP-800























































Reviews: