Clay Paky AROLLA PROFILE MP Instruction Manual Download

Page: 16 / 16

250

(9.84")

360

(14.17")

412

(16.22")

593

(23.35")

347

(13.66")

480

(18.89")

480

(18.90")

5. DIMENSIONS

THE PROJECTOR WILL NOT SWITCH ON

PROBLEMS

ELECTRONICS NON-OPERATIONAL

DEFECTIVE PROJECTION

REDUCED LUMINOSITY

POSSIBLE CAUSES

CHECKS AND REMEDIES

No mains supply.

Light source exhausted or defective.

Signal transmission cable faulty or disconnected.

Incorrect addressing.

Fault in the electronic circuits.

Lenses broken

Dust or grease deposited.

Check the power supply voltage.

Call an authorised technician.

Replace the cables.

Check addresses (see instructions).

Call an authorised technician.

Clean (see instructions).

6. CAUSE AND SOLUTION OF PROBLEMS

–

CLAYPAKY

S.p.A.

- Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - www.claypaky.com

Summary of Contents for AROLLA PROFILE MP

















Search results

Summary of Contents for AROLLA PROFILE MP

Reviews:

Related manuals for AROLLA PROFILE MP

Brands by name

Popular brands

Clay Paky AROLLA PROFILE MP, Instruction Manual

Search results

Summary of Contents for AROLLA PROFILE MP

Reviews:

Related manuals for AROLLA PROFILE MP

Brands by name

Popular brands