background image

SAFETY PRECAUTIONS

For your safety, please read and observe the following safety precautions:

1.

CAUTION: THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL
TIMES IN ACCORDANCE WITH THESE INSTRUCTIONS.

2.

WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH THIS
STANDARD SHALL COMPLY WITH THE REQUIREMENTS OF AS/NZS 4013
WHERE REQUIRED BY THE REGULATORY AUTHORITY, I.E. THE APPLIANCE
SHALL BE IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4013’.

3.

WARNING: ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS CONSIDERED AS
BREACHING AS/NZS 4013.

4.

CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM COMPONENTS FROM
DIFFERENT SOURCES OR MODIFYING THE DIMENSIONAL SPECIFICATION
OF COMPONENTS MAY RESULT IN HAZARDOUS CONDITIONS. WHERE
SUCH ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE
CONSULTED IN THE FIRST INSTANCE.

5.

CAUTION: CRACKED AND BROKEN COMPONENTS, e.g. GLASS PANELS OR
CERAMIC TILES, MAY RENDER THE INSTALLATION UNSAFE.

6.

WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR
REKINDLE THE FIRE.

7.

WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE
VICINITY OF THIS APPLIANCE WHEN IT IS OPERATING.

8.

WARNING: DO NOT STORE FUEL WITHIN HEATER INSTALLATION
CLEARANCES.

9.

CAUTION: THIS APPLIANCE SHOULD NOT BE OPERATED WITH A CRACKED
GLASS.

10.

place wood, paper, clothes, furniture, or any combustibles etc. within

DO NOT

heater installation clearance areas.

11.

install heater or flue any closer than compliance clearances.

DO NOT

12.

DO NOT BURN WET OR GREEN WOOD.

13.

burn rubbish or treated timber as fumes may be dangerous.

DO NOT

14. CAUTION: THE USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD

AS A FUEL CAN BE HAZARDOUS.

15.

over fire heater. Always operate with door closed. Turn fan on when burning

DO NOT

on high.

16.

install heater with over length flue as this may over fire heater. Check flue

DO NOT

draught when more the 5.4 metres of flue are used.

17.

let small children near heater while operating. The glass and front are HOT.

DO NOT

18. PLEASE NOTE A PERMIT MAY BE REQUIRED FOR INSTALLATIONS IN SOME

STATES.

Page 2

DISCLAIMER

Clean Air Woodheating Pty Ltd does not accept any responsibility whatsoever for errors and omissions
or their interpretation regarding building codes and AS/NZS 2918.
It is the responsibility, entirely of the purchaser to investigate local council building requirements to
ensure their Clean Air wood heater is installed correctly in accordance with AS/NZS 2918.
All information is current at time of printing. Clean Air Woodheating relies on the reports from testing
authorities in any claims made regarding adherence to Australian standards and EPA requirements.
Clean Air Woodheating accepts no reliability for the testing authorities interpretation of AS/NZS 2918.
The manufacturer reserves the right to alter designs and specifications at any time.

Summary of Contents for Edwardian Large



















Reviews: