I
NSTRUCTIONS
F
OR
N
EW
C
LEAN
R
EMOTE
CR3BCB T
HAT
H
AS
B
UTTON
A
T
T
HE
B
OTTOM
O
F
T
HE
R
EMOTE
If you
do not
have an individual cable box in each guest room, then turn sheet over to
page 1
IF YOU HAVE A TV AND AN INDIVIDUAL CABLE BOX IN EACH GUEST ROOM, START HERE :
1.First step is to program the TV. The second step will then be to program the cable box.
2.
It is important that after you set up the TV you don’t change the channels until after you complete
the next step of setting up cable box.
3.
Turn on the TV and the Cable Box should also be on. Then
stand back about 5 feet from the TV. Point the remote
at the CENTER of the front panel of the TV
. It will not be necessary to point the remote at that exact area once
the remote is set-up.
4.Press
and firmly
Hold down
the
Setup button
, do not release. The LED will blink once and then after 7 seconds it
will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off, immediately
remove your finger from the Setup button; the code automatically locks in.
5.
Now test the remote by pressing the TV Power button testing
On/Off and then the
/-
,
DO NOT PRESS C/-
buttons
as you may change input on TV.
If power and volume buttons work correctly on the remote then proceed to step #6.
If you accidentally changed the input on the TV, manually change it back from the TV’s control panel
and then try power and volume buttons
ONLY
.
If the power and volume keys are not working properly, you may not have an exact code match. Start
again at step #3, the code search will continue where it left off. Once you have the correct code, go to
step #6 to program the cable box.
6.To Program the Cable Box
make sure the cable box and TV are on. Next,
Hold Down
the button
and CC button
at the same time
and wait until the LED light blinks quickly 3 times. Then immediately release both buttons. Now
point the remote toward the cable box and TV and try the channel up and down buttons as well as the the channel
numbers. If the channels change correctly, make sure volume and TV power on and off work and if they do ,you
are done.
7.
If the channels are not changing properly make sure the
TV is on
and this time
turn the cable box OFF
. (If setting up
a box that does not have a separate power button and is always on, see notes at the bottom of this page.)
NOTE: this time
DO NOT HOLD THE CC button down, just press and firmly hold down the button
while pointing
the remote at the cable box ( not the TV). The LED will blink once and then after 10 seconds it will initiate code
search. The LED will continue to blink every 2 seconds. When the cable box turns ON,
immediately
remove your
finger from the button and the code automatically locks in.
Now turn the CABLE box off and then back on by pressing the
CBL button
once (
Not
the TV power button or
button
). Next test channel up and down and the channel numbers. If the channels change correctly, make sure
volume and TV power on and off operate, if so, you are done. If it is not working properly start again at step #6.
IMPORTANT TROUBLESHOOTING INFORMATION
A.
If you think you missed the TV code or are testing remote on different brand TV’s,
or are having difficulty
operating TV; first, reset the remote by
pressing and holding
the
Setup button for 2 seconds
and then
while still
pressing the Setup button down press and hold down the CC button
at the same time until the LED light blinks
quickly 3 times, immediately release both buttons. You have now reset the code list back to the beginning. Go
back to step #1 and repeat all steps #1 through #7 again.
B.
Reset remote to work TV only without a cable box.
If you’ve already set up the remote to work both a TV and a Cable Box and now wish to operate TV only without a
cable box. Hold down the button and SETUP button together until the remote blinks 3 times quickly and
immediately release both buttons. Then turn over the page and start at step 1 for TV only.
Notes:
A)
If setting up a cable box that does not have a separate power button and is always on. Follow the
instructions on step 7, but release
immediately if you see any change on the TV’s picture or the lights on
the box.
B)
If your cable box does have a separate power button, once you have set-up the cable box to work with
the Clean Remote it can be powered on or off by pressing the CBL button.
