Clean Water Systems J-PRO-22 Installation & Start?Up Manual Download | Manualshive

Page: 6 / 16

background image

J-PRO-22 Alum Guide Rev 0021622 Page | 6

You may cut off the 110-style plug and wire a 220-style plug, and then plug that into a

dedicated 220- style wall outlet.

Install a dedicated wall outlet that is wired to the pressure switch and powered up

whenever the well pump turns on.

The J-Pro-22 is a dual voltage pump. It has a 110 volt- style plug but can run on 220v or

110v. It uses a maximum of 22 watts power when running.

Use Pre-Wired Flow Switch Option

«
...
4
5
6
7
8
...
»

Summary of Contents for J-PRO-22

















Reviews:

No comments

Related manuals for J-PRO-22

Brand: CAB Pages: 22

Ultraklean 2000

Brand: AquaScape Pages: 28

BASIKA rho NS 10

Brand: Magus Pages: 30

Brand: WATSEA Pages: 9

SWIMCLEAR C3030EURO

Brand: Hayward Pages: 69

Brand: Rangemaster Pages: 4

Nitrogen Pac SC-W

Brand: UNITED Pages: 112

Brand: ZIEHL-ABEGG Pages: 44

Brand: Alamo Water Pages: 44

Brand: Electrolux Pages: 4

Brand: Electrolux Pages: 16

AquaSense PUREADVANTAGE

Brand: Electrolux Pages: 5

Brand: Electrolux Pages: 72

Brand: ROSEDALE Pages: 4

Brand: Clean Air Pages: 36

Viridian Delta-T

Brand: Taco Pages: 8

Brand: Taco Pages: 8

Pantera II Series

Brand: onga Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands