About
The Seriously Pro Racing F3 NEO FPV Stack has Flight Controller (FC), Video Transmitter (VTX), On-Screen-Display
(OSD) and Power Distribution Board (PDB) features that makes it the system of choice for any new low-profile
multi-rotor build.
The NEO system comprises of two boards, a bottom board with the FC/PDB and a top board with an OSD and
VTX.
The Cleanflight OSD software is all new and supports a variety of features with more to come. The USB socket on
the FC allows configuration and firmware flashing via the cleanflight configurator. No additional software, other
than drivers, is needed.
The FC also has race timing transponder components. When purchased with a transponder LED and code it can
be used as a race transponder for lap/race timing.
Features / Specification
FC/PDB Board
• Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and faster
ARM-Cortex M4 core.
• Features the latest accelerometer and gyro technology (ICM20602) via SPI connection.
• MicroSD-Card socket for black box flight log recorder - optimize your tuning and see the results of your setup
without guesswork.
• Built in amperage/current monitoring sensor, 110A.
• Telemetry support (FrSky, SmartPort/S.PORT, IBus, etc).
• 5 Serial ports. e.g. Re Tel 3 Spare - None shared with the USB.
• Built-in LC-Filter for clearer video.
• Race transponder built in - just turn up at a race and have your lap times recorded.
• Boot button for easy DFU/USB flashing.
• Wire up using solder pads for ESC connections and cable or header pins for receiver.
• 6 PWM output lines for ESCs and Servos. 4 are arranged for easy wiring on each corner of the board.
• Supports direct connection of SBus, SumH, SumD, Spektrum1024/2048, XBus/IBus receivers. No external invert-
ers required (built-in).
• Supports direct connection of 3.3v Spektrum Satellite receivers via 3 pin through-hole JST-ZH connector.
• Supports PPM receivers.
• Micro USB socket.
• Dedicated output for programmable LEDs - great for orientation, racing and night flying.
• Dedicated I2C/UART3/UART5 port for connection of OLED display, GPS receivers, external MAG/BARO without
needing flight battery.
• Voltage monitoring for battery, 12v and 5v supplies.
• Analog RSSI monitoring.
• Buzzer port for audible warnings and notifications.
• Developer friendly debugging port (SWD) unbrickable bootloader.
• Symmetrical design for a super tidy wiring, just 4 wires per corner to each ESC and you’re done!
• JST-SH sockets only for I2C/UART3/UART4 and SWD. UART1 available on through-hole stacking pins and bro-
ken out on OSD/VTX board.
• 12 position connector for stacking the OSD/VTX board. (SPI/CS1/CS2/VSYNC/HSYNC/VTX ENABLE/BUT-
TON),
• Through-hole solder pads AND solder-less connections for receiver via PicoBlade connector.
• Through-hole solder pads for Transponder IR LED.
• Solder pads for RSSI.
• Solder pads for LED Strip.
• Solder pads for ESC power. (2 by each corner)
• Solder pads for ESC signal and ground. (2 by each corner).
• Solder pads for 2x additional PWM outputs (e.g. for pan / tilt servos).
• Direct connection for XT60 socket. (Through hole).
• Flashing via USB or serial port.
• Standard 30.5mm mounting holes, board fits in most 36x36x mounting spaces.
• Board is 45x50mm with corner cut-outs to allow frame clearance.
• LEDs for 3v (Blue), 5v (Green) and 12v (Yellow) supplies.
• Two status LEDs (Red, White) for easy diagnostics/flight mode indications.
SPRacingF3NEO
http://seriouslypro.com - http://cleanflight.com
Page 2
