background image

17

SIGNS OF AIRLOCK

◙ Bubbles

◙  The ball is bobbing 

    up and down

Bubbles

The ball is bobbing 

up and down

Submerge

in the 

cleaning 

solution

Do not

expose 

to air 

while 

operating

chemical feed 

adjustable flowmeter

OPTIONS

IMAGES AND ILLUSTRATIONS ARE FOR REFERENCE ONLY.   ACTUAL PRODUCTS MAY NOT BE EXACTLY AS SHOWN.

chemical feed 

& mixing quick 

connect

1. ADJUSTABLE CHEMICAL FEED SYSTEM

image 19.1

image 19.2

image 19.4

 SCALE 

WATER:CHEMICAL

60:1

30:1

20:1

15:1

12:1

(EXAMPLE: MIXTURE RATE:
SCALE 1=60 GALLON OF WATER TO 1 GALLON OF CHEMICAL)

image 19.3

NOTE: 

You may pre-spray your cleaning area with a pre-spray solution prior to extracting or you may use the  

 

 

      CHEMICAL FEED AND MIXING SYSTEM to mix in the cleaning solution automatically with water while    

 

      cleaning.

To  use  the ADJUSTABLE  CHEMICAL  FEED AND  MIXING  SYSTEM,  have  a  bottle  or  bucket  of  cleaning  solution 

ready. (See image 19.4).  If you are using a cleaning chemical in powder form, mix it with water thoroughly, make sure 

it is fully dissolved. Any undissolved powder can clog up the flowmeter, spray jets, and other parts on the extractor 

damaging them in the process.

A.  Place the bottle or pail of cleaning solution to the the side of the extractor. Put the end of CHEMICAL FEED LINE  

 

all the way to the bottom of the bottle or bucket of cleaning solution. (See image 19.4). If the CHEMICAL FEED  

 

LINE is not fully submerged in the solution, air can get into the system and it may disable it.

B.  Turn pump switches “ON”.

C.  Open the adjustable flowmeter fully by turning it counter clockwise. (See image 19.1 and 19.2)

 

If there is any air in the system, you will see air bubbles in the adjustable flowmeter and the ball inside will be

 

bobbing up and down. (See image 19.2) Then, pull the trigger valve from wand or any attached tools to let the air  

 

out. (See the “How to Bleed” page) 

D.  Adjust the Adjustable flowmeter according to the chart. (See image 19.3) Mixture rate should be based on the  

 

condition of the carpet or upholstery you are cleaning. When setting the flowmeter, open the solution valve on the  

 

wand. 

Summary of Contents for CF-100 Series

























Reviews: