background image

 

   

 

 

 

 

 

 

 

 

 

 

29 

APPENDIX -

 

Section E

 

ClearWater Tech, LLC. Limited One-Year Warranty

 

Summary of the Warranty 

ClearWater Tech, LLC (“CWT”) makes every effort to assure that its products meet high quality and durability standards and warrants the products it manufactures 

against defects in materials and workmanship for a period of one (1) year, commencing on the date of original shipment from CWT, with the following exceptions: 1) 

The warranty period shall begin on the installation date if the installation is performed within 90 days of the original shipment from CWT; 2) The warranty period shall 

begin on the date of the bill of sale to the end user if the installation date is more 90 days after the original shipment date. To validate the warranty, a warranty card, 

accompanied by a copy of the bill of sale, must be returned to CWT and must include the following information:

• End user name 

• Complete address, including telephone number 

• Date installed 

• Complete model and serial number information 

• Name of company from which the unit was purchased 

Repairs and replacement parts provided under this warranty shall carry only the unexpired portion of this warranty or 90 days, whichever is longer.

 

 

Items Excluded from the Warranty 

This warranty does not extend to any product and/or part from which the factory assigned serial number has been removed or which has been damaged or rendered 

defective as a result of:

• An accident, misuse, alteration or abuse 

• An act of God such as flood, earthquake, hurricane, lightning or other 

disaster resulting only from the forces of nature 

• Normal wear and tear 

• Operation outside the usage parameters stated in the product user’s manual  

• Use of parts not sold by CWT  

• Service or unit modification not authorized by CWT  

• Check valve/solenoid valve failure 

• Damage which may occur during shipping 

• Failure to meet service requirements as outlined in the I & O manual 

 

Obtaining Service Under the Warranty 

Any product and/or part not performing satisfactorily may be returned to CWT for evaluation. A Return Goods Authorization (RGA) number must first be obtained by 

either calling or writing your local authorized dealer, distributor or CWT direct, prior to shipping the product. The problem experienced with the product and/or part 

must be clearly described. The RGA number must appear prominently on the exterior of the shipped box(es). The product and/or part must be packaged either in its 

original packing material or in comparable and suitable packing material, if the original is not available. You are responsible for paying shipping charges to CWT and 

for any damages to the product and/or part that may occur during shipment. It is recommended that you insure the shipment for the amount you originally paid for the 

product and/or part. 

 

If, after the product and/or part is returned prepaid and evaluated by CWT, it proves to be defective while under warranty, CWT will, at its election, either repair or 

replace  the  defective  product and/or  part  and  will  return  ship  at  lowest  cost  transportation prepaid  to  you 

except  for  shipments  going  outside  the  50  states  of  the 

United States of America. 

If upon inspection, it is determined that there is no defect or that the damage to the product and/or part resulted from causes not within the 

scope of this limited warranty, then you must bear the cost of repair or replacement of damaged product and/or part and all return freight charges. Any unauthorized 

attempt by the end user to repair CWT manufactured products without prior permission shall void any and all warranties. For service, contact your authorized dealer or 

distributor or CWT direct at (805) 549-9724. 

 

Exclusive Warranty 

There  is  no  other  expressed  warranty  on  CWT  products  and/or  parts.  Neither  this  warranty,  nor  any  other  warranty,  expressed  or  implied,including  any  implied 

warranties or merchantability of fitness, shall extend beyond the warranty period. Some states do not allow limitation on how long an implied warranty lasts, so that the 

above limitation or exclusion may not apply to you. 

 

Disclaimer of Incidental and Consequential Damages 

No responsibility is assumed for any incidental or consequential damages; this includes any damage to another product or products resulting from such a defect. Some 

states do not allow the exclusion or limitation of incidental or consequential damages, so that above limitation or exclusion may not apply to you. 

 

Legal Remedies of Purchaser

 

This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. 

 

THIS STATEMENT OF WARRANTY SUPERSEDES ALL OTHERS PROVIDED TO YOU AT ANY PRIOR TIME.

 

Summary of Contents for SC27P































Reviews: