Clemco ZERO Blast Cabinets Manual Download

Page: 17 / 17

MEDIA RECLAIMER / SEPARATOR

Page 16

•

www.clemcoindustries.com

•

Manual No. 23438

•

Rev. E

9.6

Metering Assemblies, Suction Systems

Figure

Item Description

Stock

No.

Metering

valve

assembly, BNP .................12417

Stem, metering adjusting ..........................23097

Screw, adjusting ........................................23098

Nut, adjusting stem lock ............................23099

Plug,

1" plastic ...........................................12011

Fitting, hose, 3/8" NPT x 1/2" barb ............06369

Nipple

1" x close ........................................01701

Metering

valve

assembly, Lexan ...............12420

Manifold, multiple metering valve, 2" inlet

for use with up to 6 blast guns ..................12322

10.

Manifold, multiple metering valve, 3" inlet

for use with up to 12 blast guns ................16202

11.

Metering stem assembly (items 2, 3, & 4) .23889

Figure

Summary of Contents for ZERO Blast Cabinets


















Search results

Summary of Contents for ZERO Blast Cabinets

Reviews:

Related manuals for ZERO Blast Cabinets

Brands by name

Popular brands

Clemco ZERO Blast Cabinets, Manual

Search results

Summary of Contents for ZERO Blast Cabinets

Reviews:

Related manuals for ZERO Blast Cabinets

Brands by name

Popular brands