USING CLEVERSPA
®
FOR THE FIRST TIME
If you are using your hot tub for the first time, or
have changed the water, you will need to chemically
‘Shock’ your hot tub water. Shocking the water in your
CleverSpa® hot tub will sanitise the water ensuring it is
safe to bathe, destroying any bacteria.
Good chemical maintenance is very important and
will reduce the number of times your CleverSpa®
requires fresh clean water.
HARDWATER/LIMESCALE
If you live in an area with hard water, you may
experience limescale build up and residue in your
CleverSpa® pump & heating system which could
significantly reduce the lifespan of some internal
components, stopping the hot tub from working.
In order to reduce the effects of limescale build up
please check the water hardness in your area. If you
are affected please ensure that CleverSpa® Descaler is
used weekly to prevent scale formation and build up.
CLEANING YOUR CLEVERSPA
®
To clean your CleverSpa
®
, use soap and water then
rinse thoroughly.
PLEASE NOTE
: do not use hard
brushes or abrasive cleaners. For best results we
recommend the use of our CleverSpa® Sponge.
REPAIRING PUNCTURES IN YOUR CLEVERSPA
®
If your CleverSpa
®
is torn/punctured, use repair
patches. Completely dry area to be repaired, apply
strong adhesive to repair patch and then cover the
damaged area. Smooth the surface to remove
any air bubbles. Leave to dry for 12 hours before
using the CleverSpa
®
.
HOW TO EMPTY YOUR CLEVERSPA
®
1. Remove CleverSpa
®
plug from electrical mains.
2. Unscrew cap from drainage outlet
(L)
below pump
system of CleverSpa
®
. Ensure Drainage Plug
(G)
is still inserted to prevent unexpected draining.
3. Screw inflation hose
(D)
onto the water outlet
(L)
and direct open end of hose appropriately.
4. Remove drainage plug from outlet within floor
of CleverSpa
®
, so water can flow out.
5. Once drained use a sponge to absorb excess water;
then operate air jet function for up to 20 minutes (one
full cycle) to drain any water and dry out the pipeline.
If not completely dry after first cycle – repeat.
6. When draining has finished, remove inflation
hose
(D)
and replace drainage plug
(G)
and
outlet cap
(L)
.
HOW TO DEFLATE YOUR CLEVERSPA
®
1. Locate the black two-part air valve
(K)
.
2. Fully unscrew and remove rapid deflation
air valve by turning anti-clockwise
(K)
.
3. Fold hot tub away carefully to remove as much
air as possible through the open valve.
STORING YOUR CLEVERSPA
®
Make sure all water is completely drained from
the CleverSpa
®
and pump system. This is vital in
extending the life of your CleverSpa
®
. We recommend
the use of a wet/dry vacuum to help blow out/
suck up water from pipes and pump lines. Remove
filter cartridge. CleverSpa
®
should be placed in bag
provided and stored in a dry place, raised off floor
and away from extreme temperatures.
Please note:
When not in use, store in a place that is dry and a
moderate temperature, as subzero temperatures
can severely damage your CleverSpa
®
.
CORRECT INFLATION
How do I know my hot tub is inflated correctly?
Here is an example image of the correct inflation
level for a standard hot tub. Once inflated correctly
you should be able to push your hand approximately
4-5cm into the top rim using moderate force creating
creases similar to the picture above. Keeping your
hot tub inflated to the correct pressure ensures
optimum liner performance, reducing the risk of
ripping and seam failures.
OVER INFLATION
How do I know how much air should I inflate
my hot tub with?
If you are not able to push your hand into the
rim of the hot tub by approximately 4-5cm with
moderate force, then your hot tub is over-inflated.
An over inflated hot tub can result in ripping or
disfiguring the liner and seriously damaging the
hot-tub all-together.
14
MAINTENANCE & REPAIR
