Clevo P6x0Hx User Manual Download

Page: 212 / 368

Modules

6 - 54 Sound Blaster Audio

Testing 5.1 Surround Sound (Advanced Settings)

If you are using the

Sound Blaster X-Fi MB5

control panel (

Advanced Settings

)

to test your headphones/speakers, set up as a 5.1 surround sound system with the mi-
crophone jack enabled as the "Center/Subwoofer" (see

Figure 2 - 3 on page 2 - 5

)

in the

Realtek HD Audio Manager

, you may not hear the low Subwoofer test tone

as some headphones/speakers do not support low frequencies.

If your headphones/speakers do not support low frequencies then follow the instruc-
tions below to obtain an effective sound test.

Attach your headphones/speakers to the headphone out jack.

Run the

Sound Blaster X-Fi MB5

control panel from the notification area of the

taskbar (or from the item in the Start screen).

Click

ADVANCED SETTINGS > SPEAKERS/HEADPHONES

Select

5.1 Surround

under

Speakers/Headphones

Configuration

Click to place checks in the

Bass Redirection/Subwoofer Gain

check boxes.

Move the slider for

Crossover Frequency

to its maximum setting.

Click

Test

to hear the sound.

Your headphones/speakers will now be configured for 5.1 Surround.

Figure 6 - 34

Bass Management

Sound Blaster X-Fi

MB5 Advanced

Settings

Summary of Contents for P6x0Hx

















































































































































































































































































































































































Search results

Summary of Contents for P6x0Hx

Reviews:

Related manuals for P6x0Hx

Brands by name

Popular brands

Clevo P6x0Hx, User Manual

Search results

Summary of Contents for P6x0Hx

Reviews:

Related manuals for P6x0Hx

Brands by name

Popular brands