background image

Preface

  V

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1.

Don’t drop it, or expose it to shock.

 If the computer falls, the case and the components could be damaged.

2.

Keep it dry, and don’t overheat it.

 Keep the computer and power supply away from any kind of heating element. This 

is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

3.

Follow the proper working procedures for the computer

. Shut the computer down properly and don’t forget to save 

your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not expose the computer 
to any shock or vibration.

Do not place it on an unstable 
surface.

Do not place anything heavy 
on the computer.

Do not expose it to excessive 
heat or direct sunlight.

Do not leave it in a place 
where foreign matter or mois-
ture may affect the system.

Don’t use or store the com-
puter in a humid environment.

Do not place the computer on 
any surface which will block 
the vents.

Do not turn off the power 
until you properly shut down 
all programs.

Do not turn off any peripheral 
devices when the computer is 
on.

Do not disassemble the com-
puter by yourself.

Perform routine maintenance 
on your computer.

Summary of Contents for PD50PNN












































Reviews: