Clifford III Owner'S Manual Download

Page: 15 / 16

User- selectable fea tures

Your Smart Remote Starter III system comes from the factory with all of its features
pre-programmed as noted in the following table. No programming is required, but if you
wish to change any of the settings, just use the procedure below. To restore the feature to
its factory setting, just repeat the procedure:
1. Select the feature you wish from the table. Note the number of momentary taps.
2. Turn your vehicle’s ignition switch to its “ON” position.
3. Enter your valet code as noted on page 10-11, then immediately tap and release

the momentary side of the switch the number of times corresponding to the
feature you wish to change. Beginning with the 4th tap, the LED will blink each
time you tap thereafter to help you count (e.g., 5 blinks for feature 8; 9 blinks for
feature 12, etc.).
a. If noted, perform the “Secondary action.”
b. If noted, wait for the “Completion confirmation.”

4. Turn the ignition off. Repeat steps 1-4 for any other feature you wish to program.

Feature

Factory

setting

# of

taps

Secondary action

Completion

confirmation

Result

Battery Mode

AutoStart

OFF

—

2 flashes=ON

Change from OFF to ON

Temperature Mode

AutoStart

OFF

—

2 flashes=ON

Change from OFF to ON

AutoUnLock

—

1 flash=OFF

2 flashes=ON

Change from OFF to ON

or vice-versa

AutoLock

—

1 flash=OFF

2 flashes=ON

Change from OFF to ON

or vice-versa

AutoActivation

of starter interrupt

—

1 flash=OFF

2 flashes=ON

Change from OFF to ON

or vice-versa

AutoActivation

of door locks

OFF

—

1 flash=OFF

2 flashes=ON

Change from OFF to ON

or vice-versa

Feature 10 requires installer programming. Do not change the status of feature 10.

Set new valet code

See Setting your own secret valet code on page 11.

Add a

new remote control

—

Press button 1 on the

new remote control

2 flashes

New remote control has

been added

Features 13-14 require installer programming. Do not change the status of feature 13 or 14.

Set headlight duration

✱

30 sec.

After 15th tap, start

counting. Turn ignition off

after desired duration

—

New headlight duration

has been set

✱

WARNING: DO NOT change the headlight duration if the system automatically

closes the power windows every time you remotely lock the doors. Doing so may

damage your vehicle’s window/sunroof motors.

Summary of Contents for III

















Search results

Summary of Contents for III

Reviews:

Related manuals for III

Brands by name

Popular brands

Clifford III, Owner'S Manual

Search results

Summary of Contents for III

Reviews:

Related manuals for III

Brands by name

Popular brands