background image

 

 

ClimaCheck Gateway NX400 Hardware Manual 

 2020-03-26  Page 15 of 41 

 

3.5

 

Show IP-addresses 

To show what IP-addresses the Gateway uses on LAN, WiFi and GPRS connections: 

 

Press ESC to enter the Main menu 

 

Press Down until “Monitor” 

appears in the display  

 

Press SEL to enter Monitor menu 

 

Press Down until “Show IP

-

addresses” 

is showed in the display 

 

Press OK 

IP-addresses for all network interfaces is presented. To change communication settings, see 
section 3.11. 

3.6

 

Show IODevices 

To show status and address for all configured Modbus units: 

 

Press ESC to enter the Main menu 

 

Press Down until “Monitor” 

appears in the display  

 

Press SEL to enter Monitor menu 

 

Press Down until “Show IODevices” 

appears in the display 

 

Press OK 

 
Device name, Modbus address and status are displayed. Status is OK when communication is 
working and Error if the unit can

t connect to the IODevice. After a number of failed attempts, the 

device is disabled and get Status Disabl. The unit will enable the devices again once every hour to 
try to restore communication. The most common devices are listed in Table 4 below, see section 
4.6 for more information about configuration of IODevices.     
  

Table 4 

Device 

Description 

IAIO 

Internal Analog Input and Output on the Gateway   

R560 

ClimaCheck R560 analog input module 

PScout 

Power Scout power meter  

1W 

Internal 1-Wire module  

 
 

 

Figure 8, "Show IODevices" menu 

Summary of Contents for NX400










































Reviews: