background image

 

 

ClimaCheck Gateway NX400 Hardware Manual 

 2020-03-26  Page 2 of 41 

 

Safety Precautions

 

 

Read the instruction manuals for all relevant equipment carefully before 
starting to use ClimaCheck Performance Analysing systems.

 

If equipment is used in a way not specified by producer the protection and safety 
provided may be impaired. 

For activities related to electrical systems, pressurised systems as well as systems 

charged with refrigerants certifications/licenses are required in most countries. 

ClimaCheck products are only intended for use by competent technicians/engineers with on each 
market required certifications/licenses.  

Any work with electricity, pressurised systems and refrigerant involve potential dangers to human 
health and system integrity if not conducted with caution. In many cases the value of products or 
cost of production loss represents great values. ClimaCheck do not assume any responsibility for 
injuries or costs occurring if failures are caused in connection with measurements. It is the user 
that must evaluate if an installation can be carried out without risks to cause injuries and/or 
damage. Installation should only be carried out when it can be done with proper safety margins.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ClimaCheck 

distributes this document without warranty for the contents. Furthermore, 

ClimaCheck 

reserves the right to make changes, amendments and cut outs in this document 

without any further notice. The reason can be printing errors, faulty information, or improvements. 
These kinds of changes are always included in new editions of this document. 

 

All rights reserved. 

 

© ClimaCheck Sweden AB 

Summary of Contents for NX400










































Reviews: