4
Step 5.
Repeat Step 3 and Step 4 to insert the black wire. Inserting the two wires to the same side (right), as shown
below, of the two connectors provides an easier installation in the following steps.
Step 6.
Insert the AC wires to the two connectors respectively, as shown below. Use a pair of tweezers to turn the Battery Switch
to ON position (left side), the rechargeable battery will begin to charge.
Figure 3
Figure 4
Step 7.
Put the Z-Wave gateway or control panel into
Inclusion
or
Learning
mode (please refer to the Z-Wave gateway or
control panel manual).
Step 8.
.
Within 1.5 seconds, press the Function button 3 times. The Smoke Detector will emit a 2-tone beep and the LED will
turn on for ~2 seconds. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in
process.
If the sensor has already been
included
(learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be
learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see
Exclusion
) before attempting to
include
it into
the current Z-Wave Gateway/Control Panel.
R
R
e
e
m
m
o
o
v
v
i
i
n
n
g
g
D
D
e
e
v
v
i
i
c
c
e
e
(
(
E
E
x
x
c
c
l
l
u
u
s
s
i
i
o
o
n
n
)
)
The Smoke Detector must be removed from existing Z-Wave network before being included into another. There are two methods
available to exclude a device.
Exclusion Mode
Put the Z-Wave gateway or control panel into
Exclusion mode
(please refer to the Z-Wave gateway or control panel manual).
Within 1.5 seconds, press the Function button 3 times and the Smoke Detector will be removed from the Z-Wave network.
Factory Reset
(Only use factory reset when network Control Panel/Gateway is missing or inoperable).
Remove the batteries of the Smoke Detector first.
Press and hold the Function button. While holding the Function button, power on the Smoke Detector by re-inserting the
batteries, wait for 20 seconds to factory reset.
<
<
N
N
O
O
T
T
E
E
>
>
Before you remove or factory reset the Smoke Detector, please ensure that the device DSK information has been removed or
does not exist in the gateway. If you remove or factory reset the device, but its DSK still exists in the gateway, the gateway will
automatically include the device again.
Factory resetting the Smoke Detector will restore it to factory default settings (excluded from the Z-Wave network). The Z-Wave
gateway or control panel will still keep its Z-Wave settings. Please refer to the gateway or control panel manual on how to
remove the Smoke Detector
’s Z-Wave settings.
R
R
a
a
n
n
g
g
e
e
T
T
e
e
s
s
t
t
To test whether the device is able to communicate with the Z-Wave gateway or control panel:
Put the gateway / panel into range test mode (Walk Test).
Press the Function button on the device.
The gateway / panel should display if the device is within the operation range (please refer to the operation manual of the
gateway / panel).
Installation
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
l
l
i
i
n
n
e
e
It is recommended that the installation site be in the center area of the ceiling.
Do not locate the detector in the following locations:
The Kitchen
– Smoke from cooking might cause an unwanted alarm.
Near a ventilating fan, florescent lamp or air-conditioning equipment
– air drafts from them may affect the
sensitivity of the detector.
Near ceiling beams or over a cabinet
– stagnant air in these areas may affect the sensitivity of the
detector.
In the peak of an “
A
” frame type of ceiling.
