26
CONSIGLI PRATICI DI INSTALLAZIONE
Posizionamento:
- Osservare scrupolosamente gli spazi di rispetto indicati a ca-
talogo.
Collegamenti elettrici:
- Consultare sempre lo schema elettrico incluso nel quadro elet-
trico, ove sono sempre riportate tutte le istruzioni necessarie
per effettuare i collegamenti elettrici.
- Dare tensione all’unità (chiudendo il sezionatore) almeno 12 ore
prima dell’avviamento, per permettere l’alimentazione delle re-
sistenze del carter. Non togliere tensione alle resistenze durante
i brevi periodi di fermata dell’unità.
- Prima di aprire il sezionatore fermare l’unità agendo sugli appositi
interruttori di marcia o, in assenza, sul comando a distanza.
- Prima di accedere alle parti interne dell’unità, togliere tensione
aprendo il sezionatore generale.
- È vivamente raccomandata l’installazione di un interruttore ma-
gnetotermico a protezione della linea elettrica di alimentazione
(a cura dell’installatore).
- Collegamenti elettrici da effettuare:
◊
Cavo di potenza tri terra;
- Collegamenti elettrici opzionali da effettuare:
◊
Consenso esterno;
◊
Riporto allarme a distanza.
Collegamenti idraulici:
- Sfiatare accuratamente l’impianto idraulico, agendo sulle
valvoline di sfiato. Questa procedura è particolarmente impor-
tante in quanto anche piccole bolle d’aria possono causare il
congelamento dell’evaporatore.
- Scaricare l’impianto idrico durante le soste invernali o usare
appropriate miscele anticongelanti.
- Realizzare il circuito idraulico includendo i componenti indicati
negli schemi raccomandati (vaso di espansione, serbatoio
d'accumulo, valvole di sfiato, valvole di intercettazione, valvola
di taratura, giunti antivibranti, ecc.).
Avviamento e manutenzione:
- Attenersi scrupolosamente a quanto indicato nel manuale di
uso e manutenzione. Tali operazioni devono comunque essere
effettuate da personale qualificato.
INSTALLATION RECOMMENDATIONS
Location:
- Strictly allow clearances as indicated in the catalogue.
Electrical connections:
- Check the wiring diagram enclosed with the unit, in wich are
always present all the instructions necessary to the electrical
connections.
- Supply the unit at least 12 hours before start-up, in order to turn
crankcase heaters on. Do not disconnect electrical supply during
temporary stop periods (i.e. week-ends).
- Before opening the main switch, stop the unit by acting on the
suitable running switches or, if lacking, on the remote control.
- Before servicing the inner components, disconnect electrical
supply by opening the main switch.
- The electrical supply line must be equipped with an automatic
circuit breaker (to be provided by the installer).
- Electrical connections to be done:
◊ Three-wire power cable + ground cable;
- Optional electrical connections to be done:
◊ External interlock;
◊ Remote alarm signalling.
Hydraulic connections:
- Carefully vent the system, by acting on the vent valves. this pro-
cedure is fundamental: little air bubbles can freeze the evaporator
causing the general failure of the system.
- Drain the system during seasonal stops (wintertime) or use
proper mixtures with low freezing point.
- Install the hydraulic circuit including all the components indicated
in the recommended hydraulic circuit diagrams (expansion vesse,
storage tank, vent valves, balancing valve, shut off valves flexible
connections, etc.).
Start up and maintenance operations:
- Strictly follow what reported in use and maintenance manual.
All these operations must be carried on by trained personnel
only.
Summary of Contents for 902-V
Page 2: ... ...