background image

 

 

 

CLEANER DRIVES 60 HZ THREE PHASE 

 
Main Fan Motor 60 Hz 
 
The main fan drive consists of a 10 HP, 1800 RPM, 230/460 Volt, 3 Phase, 60 Hertz, 
TEFC motor and drive. Wiring and motor controls are not supplied by A. T. Ferrell 
Company  (See wiring drawing) 
 
Fixed Speed Eccentric Drive  
 
The eccentric drive consists of a 2 HP, 1800 RPM, 230/460 Volt, 3 Phase, 60 Hz, T E F C  
motor and drive .  Wiring is not supplied by A. T. Ferrell Company (see wiring drawing).   
 
 
 
 

CLEANER DRIVES 60 HZ SINGLE PHASE 

 
Main Fan Motor 60 Hz 
 
The main fan drive consists of a 10 HP, 1800 RPM, 230 Volt, 1 Phase, 60 Hertz, TEFC 
motor and drive. Wiring and motor controls are not supplied by A. T. Ferrell Company  
(See wiring drawing) 
 
Fixed Speed Eccentric Drive  
 
The eccentric drive consists of a 2 HP, 1800 RPM, 230 Volt, 1 Phase, 60 Hz, T E F C  
motor and drive .  Wiring is not supplied by A. T. Ferrell Company (see wiring drawing).   
 
 
 
 

CLEANER DRIVES 50 Hz 

 
Main Fan Motor 50 Hz   
 
The main fan drive consists of a 10 HP, 1500 RPM, 200/380 Volt, 3 Phase, 50 Hertz, 
TEFC motor and drive. Wiring and motor controls are not supplied by A. T. Ferrell 
Company  (See wiring drawing) 
 
Fixed Speed Eccentric Drive  
 
The eccentric drive consists of a 2 HP, 1500 RPM, 200/380 Volt, 3 Phase, 50 Hz, T E F C  
motor and drive .  Wiring is not supplied by A. T. Ferrell Company (see wiring drawing).   
 
 
 
 

Summary of Contents for PRELUDE 526
















Reviews: