6 - REGULATION
Allumage et extinction
Pour allumer et éteindre l'unité de réglage, appuyer sur la touche OK de manière prolongée.
L'état éteint est indiqué sur l'écran avec le message OFF.
Choix du mode fonctionnement
En appuyant pendant environ 3 sec. sur la touche
,
l'écran indique les symboles qui définissent le mode de fonctionnement
courant.
En appuyant sur la touche
,
il est possible de sélectionner le mode de fonctionnement souhaité avec
séquence circulaire suivante
chauffage
→
chauffage économique
→
refroidissement
→
refroidissement économique
→
ventilation
→
chauffage
En appuyant sur la touche
[OK],
on confirme le mode affiché : les symboles clignotent durant la programmation du mode, puis
recommencent à fonctionner normalement.
Si durant la programmation du mode de fonctionnement, aucune touche n'est maintenue enfoncée pendant 10 sec, on retourne au
fonctionnement normal, sans modifier le mode de fonctionnement.
Modification de la valeur de réglage
Avec le fonctionnement normal ou avec les modes de fonctionnement qui le prévoient, il est possible de modifier la valeur de
réglage moyennant les touches [
] et [
] respectivement pour augmenter/diminuer avec pas de 0.1°.
Affichage de la température ambiante
Il est possible de visualiser la température ambiante mesurée par la sonde sur le thermostat ou sur l'unité . À partir de l'état de
fonctionnement normal :
•
appuyer brièvement sur la touche
: sur l'écran apparaît le message
Fan
et la barre des ventilateurs
•
appuyer de nouveau sur la touche
: sur l'écran apparaît uniquement le message
tA.
•
appuyer sur la touche
[OK]
pour confirmer le choix : sur l'écran clignotera le message
tA
, pour ensuite retourner au
fonctionnement normal et pendant quelques secondes le message
tA
sera alterné à la valeur de la température ambiante.
•
Il est aussi possible de retourner au fonctionnement normal en appuyant sur la touche
OK
, la touche
ou en attendant
environ 10 sec. sans appuyer sur aucune touche.
sélection du mode de fonctionnement
augmentation du champ sélectionné
diminution du champ sélectionné
OK
confirmation de la donnée programmée / ON – OFF thermostat
État de la ventilation
mode REFROIDISSEMENT
Valeur de réglage ECO activé
Humidification active
mode CHAUFFAGE
L'unité choisit automatiquement si
chauffer ou refroidir
Compresseur actif
REMOTE
Gestion de ELFO CONTROL
Fonctionnement “normal” , HID-TI raccordé au CLIVET-BUS :
•
le thermostat HID affiche l'état de fonctionnement de l'unité à laquelle il est raccordé
•
mesure périodiquement la température/humidité de la pièce dans laquelle il est installé
•
il est possible d'utiliser les uniques 4 touches frontales (programmation utilisateur).
Fonctionnement “nolink” , HID-TI non raccordé au CLIVET-BUS :
•
le thermostat est alimenté par l'alimentation auxiliaire (la batterie doit être présente)
•
il est possible d'accéder aux boutons cachés réservés à l'installateur
•
c'est une modalité temporaire qui permet d'effectuer une “programmation avancée” de l’unité .
MODES DE FONCTIONNEMENT
6.7 THERMOSTAT HID-TI2 - OPTION
120
Summary of Contents for ELFOROOM 11
