background image

 

M03Q40G6-03 30/07/08 

pag 

43 

 

HIGH PRESSURE 

heating 

 

1. 

high air temperature (see operating limits) 

2. 

fans do not work, direction of rotation inverted 

3. 

insufficient air flow to coil  

4. 

not CONSTANT flow (for example, if the pumps 

are turned off, certain areas of the plant are 
excluded or included, other uses are isolated, etc)  

5. 

dirty air filter 

6. 

condensation gas in the cooling circuit o 

7. 

Too much refrigerant 

8. 

Check the trigger point for the manostat and 

transducer 

9. 

Manostat/transducer: loose electric 

contacts/terminals, wiring cables interrupted 

10. 

Check the manostat or transducer pressure 

control point (deposits of oil, dirt, pin blocked 
mechanically) 

 

LOW PRESSURE

 heating 

1. 

low water temperature (see operating limits) 

2. 

insufficient water flow to the exchanger (high 

thermal difference between input and output)  

3. 

not CONSTANT flow (for example, if the pumps 

are turned off, certain areas of the plant are 
excluded or included, other uses are isolated, etc)  

4. 

Dirt water filter / valves open /air bubbles in the 

plant 

5. dirty 

exchanger 

6. 

Manostat/transducer: loose electric 

contacts/terminals, wiring cables interrupted 

7. 

refrigerant circuit empty, visible leaks of 

refrigerant/oil, insufficient charge 

8. 

dryer filter clogged  

9. thermostatic 

device 

not operating correctly 

10. 

Check the trigger point for the manostat and 

transducer 

11. 

Check the manostat or transducer pressure 

control point (deposits of oil, dirt, pin blocked 
mechanically) 

 

 

CONVERSION TABLE FOR HEATER TEMPERATURE FOR TEMPERATURE PROBES NTC 

 

To check the reliability of the probes in the event of alarm signals, the table below shows the relationship between the 
temperature and the heater value in Ohms. 

 

Temperature Heater Temperature Heater Temperature Heater Temperature Heater 

°C 

Ω

 

°C 

Ω

 

°C 

Ω

 

°C 

Ω

 

-20,0 

67732 

1,0 

26094 

22,5 

11013 

43,5 

5146 

-19,5 

66149 

1,5 

25543 

23,0 

10805 

44,0 

5063 

-19,0 

64604 

2,0 

25005 

23,5 

10601 

44,5 

4981 

-18,5 

63097 

2,5 

24480 

24,0 

10401 

45,0 

4901 

-18,0 

61627 

3,0 

23969 

24,5 

10206 

45,5 

4823 

-17,5 

60193 

3,5 

23469 

25,0 

10014 

46,0 

4747 

-17,0 

58794 

4,0 

22982 

25,5 

9826 

46,5 

4672 

-16,5 

57429 

4,5 

22506 

26,0 

9643 

47,0 

4599 

-16,0 

56098 

5,0 

22042 

26,5 

9462 

47,5 

4527 

-15,5 

54800 

5,5 

21589 

27,0 

9286 

48,0 

4458 

-15,0 

53534 

6,0 

21146 

27,5 

9113 

48,5 

4389 

-14,5 

52300 

6,5 

20714 

28,0 

8944 

49,0 

4322 

-14,0 

51096 

7,0 

20292 

28,5 

8778 

49,5 

4256 

-13,5 

49921 

7,5 

19880 

29,0 

8615 

50,0 

4192 

-13,0 

48777 

8,5 

19085 

29,5 

8456 

50,5 

4128 

-12,5 

47660 

9,0 

18701 

30,0 

8300 

51,0 

4066 

-12,0 

46571 

9,5 

18326 

30,5 

8147 

51,5 

4005 

-11,5 

45510 

10,0 

17960 

31,0 

7998 

52,0 

3944 

-11,0 

44475 

10,5 

17602 

31,5 

7852 

52,5 

3885 

-10,5 

43466 

11,0 

17252 

32,0 

7708 

53,0 

3826 

-10,0 

42482 

11,5 

16910 

32,5 

7568 

53,5 

3767 

-9,5 

41523 

12,0 

16576 

33,0 

7430 

54,0 

3710 

-9,0 

40588 

12,5 

16249 

33,5 

7296 

54,5 

3652 

-8,5 

39676 

13,0 

15930 

34,0 

7164 

55,0 

3595 

-8,0 

38787 

13,5 

15617 

34,5 

7035 

55,5 

3538 

-7,5 

37920 

14,0 

15312 

35,0 

6909 

56,0 

3482 

-7,0 

37075 

14,5 

15013 

35,5 

6786 

56,5 

3425 

-6,5 

36252 

15,0 

14720 

36,0 

6665 

57,0 

3368 

-6,0 

35448 

15,5 

14434 

36,5 

6547 

57,5 

3310 

-5,5 

34665 

16,0 

14155 

37,0 

6431 

58,0 

3252 

-5,0 

33902 

16,5 

13881 

37,5 

6318 

58,5 

3194 

-4,5 

33157 

17,0 

13613 

38,0 

6208 

59,0 

3135 

-4,0 

32431 

17,5 

13351 

38,5 

6100 

59,5 

3075 

-3,5 

31724 

18,0 

13094 

39,0 

5994 

60,0 

3014 

-3,0 

31034 

18,5 

12843 

39,5 

5891 

60,5 

2951 

-2,5 

30361 

19,0 

12597 

40,0 

5790 

61,0 

2888 

-2,0 

29704 

19,5 

12356 

40,5 

5692 

61,5 

2822 

-1,5 

29064 

20,0 

12120 

41,0 

5596 

62,0 

2755 

-1,0 

28440 

20,5 

11890 

41,5 

5502 

62,5 

2686 

-0,5 

27831 

21,0 

11663 

42,0 

5410 

63,0 

2615 

0,0 

27238 

21,5 

11442 

42,5 

5320 

63,5 

2542 

0,5 

26659 

22,0 

11225 

43,0 

5232 

64,0 

2466 

Summary of Contents for WSH-EE 101





















































Reviews: