47
Adjusting filaments to the right length
– Push by hand on the underside of the filament
spool and pull out both filaments out until they
are somewhat longer than the edge of the pro-
tective hood.
Next time the machine is used, the filaments are
automatically trimmed to the correct length by the fil-
ament knife.
Storing, transport
Storing
– Let the machine cool off before putting it away.
– If possible, store the machine in the horizontal
position. Make sure no fuel can leak from the
carburettor.
– Attach the knife transport guard.
If necessary, remove the shaft tube and hang it up
separately.
– Slip on the covering cap to protect the shaft tube
from dirt.
When taken out of operation
For an extended period of disuse, you must remove
the fuel from the machine. This will prevent the motor
from gumming up.
– Drain the fuel tank.
– Start the motor and keep it running until it stops
of its own accord.
– Let the motor cool down completely.
– Remove the spark plug:
.
– Pour one teaspoon full of clean two-stroke
motor oil into the combustion chamber.
– Slowly pull the starter cord several times to coat
the internal components with the oil.
– Re-install the spark plug.
Store the machine in a dry place and far away from
any ignition sources such as furnaces, gas heaters,
etc.
Transport in a motor vehicle
If you are transporting your machine in a motor vehi-
cle:
– Attach the knife transport guard.
– Let the machine cool down.
– Drain the tank
– Secure the machine against slipping.
Malfunctions and troubleshooting
In the event of a malfunction…
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the
vendor. You will save yourself a lot of trouble and
possibly money too.
DANGER! Danger of injury!
Make sure no
unauthorised persons can gain access to
the machine!
DANGER! Danger of physical injury and
death!
Improperly conducted repairs may
prevent your machine from working safely.
Such repairs will endanger you and your
surroundings.
Fault/malfunction
Cause
Remedy
Motor will not start.
Is the tank empty?
Fill with fuel.
Wrong fuel or mixture?
Drain the tank and fill with the cor-
rect mixture.
Is ignition switch set to
[STOP]
?
Turn on the ignition switch.
Is the ignition cable not attached
tightly?
Push the ignition cable plug on
tightly.
Is the ignition cable plug dirty?
Clean the ignition cable plug.
Throttle not locked?
Press the throttle down to half throt-
tle and lock it in place.
Is there excess fuel inside the com-
bustion chamber?
Start the motor repeatedly without
operating the choke lever Posi-
tion
[ ]
).
If the motor will not start: remove the
spark plug and dry the electrode.
Spark plug is soiled (is the tip black-
ened with soot)?
Clean the spark plug.
The distance between the elec-
trodes of the spark plug is too large
Set the gap to 0.6 to 0.7 mm.
Spark plug defective?
Replace the spark plug.
Motor cold?
Operate the choke lever
[ ]
.
Motor will not reach its maximum
speed.
Is the air filter soiled?
Clean or replace the air filter.
GB
Motorsense_401118_401119.book Seite 47 Donnerstag, 7. April 2016 2:28 14
Summary of Contents for 401 118
