background image

TABLE OF CONTENTS 

 
1. 

Introduction 

   2 

2. Safety precaution   

 

2-3 

3. 

Intended 

use   3-4 

4. Parts supplied 

 

  

5. 

Installation 

   4-7 

6. 

Operation 

   8 

7. 

Maintenance   8 

8. 

Troubleshooting 

  8 

9. Technical data 

 

 

10. Environmental protection  

 

1. INTRODUCTION 

 
Thank you for choosing this cooker hood. 
This installation and user’s manual is designed to 
provide you with all required instructions related 
to the installation, use and maintenance of the 
appliance. In order to operate the appliance 
correctly and safety, please read this installation 
and user ’s manual carefully before installation 
and usage. 
Keep this installation and user’s manual for future 
use. Should this appliance be passed on to a 
third party, then this installation and user’s 
manual must be included. 
No liability will be accepted for damage resulting 
from improper use or non-compliance with these 
instructions. 
 

2. SAFETY PRECAUTION 

 

Important!

 Always switch off the 

electricity supply at the mains during 
installation and maintenance such as for 
light bulb replacement 

 

General 

The cooker hood is suitable for domestic use only. 
 

Children 

 Please dispose if the packaging material 

carefully. 

 Packaging material can be dangerous to 

children. 

Danger of suffocation!

 

 Children should be supervised to ensure that 

they do not play with the appliance. 

 

Installation 

 

The cooker hood must be installed in 
accordance with the installation instructions 
and all  measurements must be     followed. 

 All installation work must be carried out by a  

competent      person or qualified electrician. 

 Do not install above a cooker with a high 

level grill. 

 
 
 

 Make sure the ducting has no bends sharper 

than 90 degrees as this will reduce the 
efficiency of the cooker hood. 

 Pay attention to the sharp edges inside the 

cooker hood during installation. 

 

Electrical safety 

 Regularly check the power cord for damage. 

If the supply cord is damaged, it must be 
replaced by the manufacturer, its service 
agent or similarly qualified persons in order to 
avoid a hazard. 

 The appliance must be placed in such a way, 

that the power supply is accessible at all 
times. 

 Before connecting the appliance to the power 

supply, check that the power supply voltage 
and current rating corresponds with the power 
supply details shown on the appliance rating 
label. 

 Never use a damaged appliance! Disconnect 

the appliance from the wall outlet and contact 
your supplier if it is damaged. 

 Danger of electric shock! Do not attempt to 

repair the appliance yourself. In case of 
malfunction, repairs are to be conducted by 
qualified personnel only. 

 

To avoid damaging the cord, do not 
squeeze, bend or chafe it on sharp edges. 
Keep it away from hot surfaces and open 
flames as well.

 

 

Lay out the cord in such a way that no 
unintentional pulling or tripping over it is 
possible.

 

 

Do not open the appliance casing under any 
circumstances.

 

 

Do not insert any foreign objects into the 
inside of the casing.

 

 

Never use accessories which are not 
recommended by the manufacturer. They 
could pose a safety risk to the user and 
might damage the appliance. Only use 
original parts and accessories.

 

 

Keep the appliance away from any hot 
surfaces and open flames. Always 
operate the appliance  on a level, stable, 
clean and dry surface. Protect the 
appliance against heat, dust, direct sunlight, 
moisture, dripping and splashing water.

 

 

Do not place heavy objects on top of the 
appliance. Do not place objects with open 
flames, e.g. candles, on top of or beside 
the appliance. Do not place objects filled 
with  water,  e.g.  vases  on  or  near  the 
appliance.

 

 
 

Summary of Contents for KONVEX









Reviews: