CNBM AVANCIS POWERMAX 3.5 Safety, Installation, And Operation Manual Download

Page: 16 / 24

SAFETY, INSTALLATION AND OPERATION MANUAL

AVANCIS POWERMAX

PHOTOVOLTAIC MODULES

Operation

• Before connecting a PV system to the

grid, make sure the entire system was
checked, tested and approved in accor-
dance with the applicable regulations
for such elec trical systems.

• Depending on local regulations and

utility policies, the physical connection
to the grid and start-up of the PV sys-
tem may only be performed by an au-
thorised installer.

• PowerMax

modules do not require any

routine maintenance.

• AVANCIS recommends that PV systems

are checked periodically for any loose
mechanical and electrical connections.

• Based on regional conditions, Power-

Max

modules might be affected by

dust, dirt or other deposits on the top
surface. This could have negative ef-
fects on the electrical performance. To
clean the surface of the Power Max

modules from time to time, AVANCIS
recommends using decalcified water
and a soft cloth or sponge to clean the
front glass (avoid cleaning agents and
abrasives). Only use water with a tem-
perature that will not cause too much
thermal stress to the module.

Disclaimer of Liability

Since compliance with this Safety, Instal-
lation and Operation Manual and the
conditions and methods of handling, in-
stallation, operation, use and mainte-
nance of the PowerMax

modules are be-

yond AVANCIS’ control, AVANCIS does
not assume responsibility and disclaims li-
ability for loss, damage, injury or expense
arising out of or in any way connected
with such handling, installation, opera-
tion, use or maintenance of the AVANCIS
PowerMax

modules. AVANCIS assumes

no responsibility for any infringement of
patents or other rights of third parties
that may result from use of the Power-
Max

modules. No licence is granted im-

plicitly or otherwise under any patent or
patent rights. The information provided
in this Safety, Installation and Operation

Manual, including product specifications
(without limita tions) and suggestions, do
not constitute a warranty, expressed or
implied. AVANCIS reserves the right to
make changes to the product, specifica-
tions or this manual without prior notice.

Electrical module cables:

2.5 mm² BETAflam

Solar Power cables, 125-flex SOLAR

FRNC, halogen free, flame retardant (temperature rating: -40 °C up to +125 °C,
bending radius: 4x outer diameter)

Electrical cable connectors:

Lumberg LC4, temperature rating: -40 °C/+85 °C (IEC),

-40 °C/+90 °C (UL)

Aluminium Bus Bar:

temperature rating: -40 °C up to +95 °C

See the applicable Product Information literature and the label on the
AVANCIS PowerMax

module backside for more detailed product data.

In case of questions, please contact:

AVANCIS GmbH
Solarstrasse 3, 04860 Torgau
Germany

Phone: +49 (0)3421 7388-0
Fax: +49 (0)3421 7388-111

service@avancis.de
www.avancis.de

Electrical Ratings of the AVANCIS PowerMax

Modules after light soaking

(10 kWh/m²)

All data at Standard Test Conditions: 1,000 W/m² irradiance in the plane of module,
module temperature 25 °C and a spectral distribution of irradiance according to air
mass (AM) 1.5.

The abbreviation “mpp” stands for maximum power point.

PowerMax

120

125

130

135

140

120 W 125 W 130 W 135 W 140 W

-0/+5 % -0/+4 % -0/+4 % -0/+4 % -0/+4 %

11.4 % 11.9 % 12.3 % 12.8 % 13.3 %

12.6 % 13.1 % 13.6 % 14.2 % 14.7 %

57.4 V 58.0 V 58.6 V 59.2 V 59.8 V