background image

1

2

 

SPA CARE GUIDE 

Your  Authorized  Dealer  carries  a  wide  variety  of  care  and 
maintenance  products.  For  more  information  please  contact 
your Dealer. 

REQUIRED FILTER MAINTENANCE

Your  new  Cascade  Spa  is  equipped  with  a  filter  cartridge.  To 
ensure maximum water quality at all times, you should replace 
the filter cartridge every six months, or earlier as necessary. The 
filter cartridge is designed to be thrown away! Attempts to re-use 
the  filter  cartridge  may  result  in  the  re-release  of  unwanted 
particles back into the Cascade Spa.

PLEATCO DUAL CORE FILTERS

Your Cascade Spa/spa comes with a premium filter.  Most come 
with  equipped  with  a  Pleatco  DualCore  Filter,  which  does  a 
better  job  of  cleaning  your  spa  water  than  any  other  filter 
cartridge.  The DualCore filter has two layers of filtration media, 
the  outer  layer  and  the  inner  layer.  Both  are  engineered  to 
remove different particles from your water.   

The outer core is similar to a traditional filter which traps larger 
debris, while the inner core filters the water for particles down to 
3  microns  in  size.    The  inner  core  is  easily  removed  and  both 
filter media can be cleaned.
Keeping  your  spa  water  clean  and  refreshing  is  extremely 
important  for  your  enjoyment  of  your  Cascade  Spa.  Our 
Cascade Spas come with only the best filters available in order 
to ensure your satisfaction.

REQUIRED WATER REPLACEMENT

You should replace the Cascade Spa’s water every 3-6 months. 
The  frequency  will  depend  on  a  number  of  variables  including 
frequency  of  use,  number  of  bathers  and  attention  paid  to  the 
water quality maintenance. You will know it is time for a change 
when  you  can  no  longer  get  the  normal  feel  or  sparkle  to  the 
water, even though the key water balance measurements are all 
within the recommended ranges.

HEADREST / PILLOW CARE

The pillows can be removed for easy cleaning and maintenance. 
All  pillows  have  plugs  within  the  pillow  itself.  To  remove  the 
pillow, grab the bottom edge firmly and pull outward. 

This will allow the pillows to pop-out from the receptacle in the 
spa shell. To reinstall the pillow you will align the pillow plug with 
the receptacle. Press/hit the front side of the pillow firmly, which 
will insert the plug back into the receptacle. 

Proper  water  chemistry  must  be  maintained.  Your
Cascade  Spa  pillows  are  easily  and  quickly  damaged
when  exposed  to  unbalanced  spa  water.   

If you suspect

that your chemicals may be unbalanced, remove your pillows
immediately  until  the  water  has  been  restored  to  suggested
conditions.

Do not sit on the pillows

Do not pull on the pillows

Pillows  should  be  cleaned  using  a  soft  cloth  and  mild  soap,
then wiped with a conditioner. We recommend that pillows be
washed each time you drain you spa.

This Limited Warranty is void if  failure is caused by accident, acts 
of  nature,  acts  of  God,  or  other  causes  beyond  the  control 
of  CSMI.  Neglect,  misuse  and  abuse  include  any 
installation, operation,  or  maintenance  of  the  spa  other  than  in 
accordance  with  the  instructions  contained  in  the  owner’s 
manual  provided  with  the  spa,  including,  but  not  limited  to 
damage  caused  by operation  outside  the  range  of  34  degrees 
Fahrenheit  and  116 degrees Fahrenheit or 1 degree Celsius and 
47 degrees Celsius.

Please  be  advised  that  the  Spa  Warranty  will  become  void 
if  Coast  Spas  or  any  of  its  selling  or  servicing  agents 
determines that the spa has been exposed to Hydrogen Peroxide, 
TriChlor or any substance using it as an ingredient proven to be 
dangerous  to  the  Spa.  Any  condition  arising  from  the  use 
of  Hydrogen Peroxide or TriChlor on the spa is not a warrantable 
defect.

CASCADE SPA INTERIOR

Your  Cascade  Spa  has  a  fiberglass  reinforced  acrylic  shell. 
Generally  dirt  and  stains  will  not  adhere  to  the  surface.  To 
properly  clean  the  surface,  we  recommend  wiping  it  with  a  soft 
damp cloth (or sponge) using a low sudsing household soap or 
liquid detergent and rinsing thoroughly with fresh water. Stubborn 
dirt or stains may be removed by using Spic & Span adequately 
dissolved  in  water.  Contact  your  dealer  and  inquire  about 
maintenance packages.

DO  NOT

  use  any  cleaning  products  containing  abrasives  or 

solvents, since these could damage the surface. Harsh chemicals 
should  never  be  used  on  acrylic  surfaces.  Damage  to  the  shell 
due  to  the  use  of  harsh  chemicals  is  not  covered  under  the 
warranty. 

OWNER’S MANUAL

 

2022

 

CASCADE II

Summary of Contents for CASCADE II 2022



















































Reviews: