26
OWNER’S MANUAL
2017
REMINDER MESSAGES
GENERAL MAINTENANCE HELPS.
Reminder Messages can be suppressed by using the Preferences
Menu. Reminder Messages can be chosen individually by the Manufac-
turer. They may be disabled entirely, or there may be a limited number
of reminders on a specific model. The frequency of each reminder (i.e. 7
days) can be specified by the Manufacturer.
CHECK THE PH
May appear on a regular schedule, i.e. every 7 days. Check pH with a
test kit and adjust pH with the appropriate chemicals.
CHECK THE SANITIZER
May appear on a regular schedule, i.e. every 7 days. Check sanitizer
level and other water chemistry with a test kit and adjust with the appro-
priate chemicals.
CLEAN THE FILTER
May appear on a regular schedule, i.e. every 30 days. Clean the filter
media as instructed by the manufacturer.
Additional messages may appear on specific systems.
TEST THE GFCI (OR RCD)
May appear on a regular schedule, i.e. every 30 days. The GFCI or RCD
is an important safety device and must be tested on a regular basis to
verify its reliability. Every user should be trained to safely test the GFCI
or RCD associated with the hot tub installation. A GFCI or RCD will have
a TEST and RESET button on it that allows a user to verify proper func-
tion.
CHANGE THE WATER
May appear on a regular schedule, i.e. every 90 days. Change the water
in the spa on regular basis to maintain proper chemical balance and
sanitary conditions.
CLEAN THE COVER
May appear on a regular schedule, i.e. every 180 days. Vinyl covers
should be cleaned and conditioned for maximum life.
TREAT THE WOOD
May appear on a regular schedule, i.e. every 180 days. Wood skirting
and furniture should be cleaned and conditioned per the manufacturers
instructions for maximum life.
CHANGE THE FILTER
May appear on a regular schedule, i.e. every 365 days. Filters should be
replaced occasionally to maintain proper spa function and sanitary con-
ditions.
Additional messages may appear on specific systems.
Reminder messages can be reset from the panel.
Messages that can
be reset will appear with a “right arrow” at the end of the message. Press
the message text to reset the message.
Warning! Qualified Technician Required for Service and Installation
BASIC INSTALLATION AND CONFIGURATION GUIDELINES
Use minimum 6AWG copper conductors only. Torque field connections
between 21 and 23 in lbs. Readily accessible disconnecting means to be
provided at time of installation. Permanently connected power supply.
Connect only to a circuit protected by a Class A Ground Fault Circuit
Interrupter (GFCI) or Residual Current Device (RCD) mounted at least
5’ (1.52M) from the inside walls of the spa/hot tub and in line of sight from
the equipment compartment.
CSA ENCLOSURE: TYPE 2
Refer to Wiring Diagram inside the cover of the control enclosure.
Refer to Installation and Safety Instructions provided by the spa
manufacturer.
Warning:
People with infectious diseases should not use a spa or hot
tub.
Warning:
To avoid injury, exercise care when entering or exiting the
spa or hot tub.
Warning:
Do not use a spa or hot tub immediately following strenuous
exercise.
Warning:
Prolonged immersion in a spa or hot tub may be injurious to
your health.
Warning:
Maintain water chemistry in accordance with the Manufactur-
ers instructions.
Warning:
The equipment and controls shall be located no less than
1.5 meters horizontally from the spa or hot tub.
WARNING! GFCI OR RCD PROTECTION.
The Owner should test and reset the GFCI or RCD on a regular basis to
verify its function.
WARNING! SHOCK HAZARD! NO USER SERVICEABLE PARTS.
Do not attempt service of this control system. Contact your dealer or
service organization for assistance. Follow all owner’s manual power
connection instructions. Installation must be performed by a licensed
electrician and all grounding connections must be properly installed.
Disconnect the electric power before servicing. Keep access door closed.
