Coast Spas INFINITY EDGE SWIM Owner'S Manual Download

Page: 16 / 27

OWNER’S MANUAL

2020

LIGHTING ISSUES

PROBABLE CAUSE

RECOMMENDED ACTION

Standard light will not come on



Bulb has burnt out



Replace the light bulb

LED lighting not in sync



Burnt out bulb/connection



Contact your dealer

LED lighting won’t come on



Incorrect settings



Contact your dealer

HEAT PROBLEMS

PROBABLE CAUSE

RECOMMENDED ACTION

Water will not heat



Error message on control panel



Spa is in a different Heat Mode



Water level is too low



Poor water flow



Closed valves



Pump 1 is not running



Refer to the Reference Card for your control
panel to verify the error



Set spa to “Standard Mode”



Add water to the spa



Clean filter & check valves



Open all valves



Contact your dealer

Water is too hot



Incorrect reading



Filter cycle duration is too long



Pump speeds reversed



Verify temperature with thermometer



Reduce duration of the filter cycle



Contact your dealer

Water will not maintain heat



Cover is off for extended periods of time in
cold weather / cold wind.



Hot tub is wired for 110V and jets are on.



Put cover back onto hot tub and allow for heat
to regenerate. Call your dealer if temperature
does not increase.



Hot tubs wired for 110V only have enough
power to heat or operate pumps. Turn off jets
to power heater.

PUMPS WILL NOT PRIME

PROBABLE CAUSE

RECOMMENDED ACTION

Pump on but no water flow



Air trapped in pump



No water in the pump



Closed valves



Loosen bleed valve in skimmer



Check the fill level in the spa



Open all valves

HYDROTHERAPY JETS

PROBABLE CAUSE

RECOMMENDED ACTION

Little to no water flowing from
jets



Jets turned off



Pump not primed



Valves are closed



Diverter set to a different seat



Dirty filter



Open jet by turning the face counter clockwise



Reset breaker to allow for the spa to prime the
pump. Open bleed valve in the skimmer area



Open valves



Switch diverter



Remove and clean filter cartridge

PLUMBING SYSTEM

PROBABLE CAUSE

RECOMMENDED ACTION

Water around base of spa



Loose connections



Leak from internal fitting



Hand tighten all quick disconnects and fittings.



Check gaskets and O-rings



Contact your dealer

Summary of Contents for INFINITY EDGE SWIM




























Search results

Summary of Contents for INFINITY EDGE SWIM

Reviews:

Related manuals for INFINITY EDGE SWIM

Brands by name

Popular brands

Coast Spas INFINITY EDGE SWIM, Owner'S Manual

Search results

Summary of Contents for INFINITY EDGE SWIM

Reviews:

Related manuals for INFINITY EDGE SWIM

Brands by name

Popular brands